This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Error: Could Not Calibrate SDARM

Hi,

I am trying to run a but project on Arria 10 but I received a different error in Commands and also in Terminal.

I built a Arria 10 Soc boot from QSPI based on https://rocketboards.org/ and based on this page I tried to debug with Arm DS-5 but during a my .ds file running I received  :

"+restore u-boot-socfpga/spl/u-boot-spl-dtb.bin binary 0xFFE00000
Restoring Binary file F:\repository\yazdandoust\sc50cont\u-boot.qspi\a10_soc_devkit_ghrd\software\bootloader\u-boot-socfpga\spl\u-boot-spl-dtb.bin into memory
Restoring section S:0x00000000 to S:0x00012A00 into memory S:0xFFE00000 to S:0xFFE12A00
+symbol-file u-boot-socfpga/spl/u-boot-spl
+set $PC = $ENTRYPOINT
+thbreak *0x0
Hardware breakpoint 1 at S:0x00000000
+continue
+wait 20s
Execution stopped in SVC mode at breakpoint 1: S:0x00000000
S:0x00000000 LDR pc,[pc,#24] ; [0x20] = 0xB8
Deleted temporary breakpoint: 1
+restore u-boot-socfpga/spl/u-boot-spl-dtb.bin binary 0xFFE00000
Restoring Binary file F:\repository\yazdandoust\sc50cont\u-boot.qspi\a10_soc_devkit_ghrd\software\bootloader\u-boot-socfpga\spl\u-boot-spl-dtb.bin into memory
Restoring section S:0x00000000 to S:0x00012A00 into memory S:0xFFE00000 to S:0xFFE12A00
+symbol-file u-boot-socfpga/spl/u-boot-spl
+set $PC = $ENTRYPOINT
+thbreak spl_boot_device
Hardware breakpoint 2 at S:0xFFE01060
on file spl_a10.c, line 77
on file spl_a10.c, line 78
on file spl_a10.c, line 78
+continue
+wait 60s
Execution stopped in SVC mode at breakpoint 2: S:0xFFE01060
In spl_a10.c
S:0xFFE01060 77,1 {
Deleted temporary breakpoint: 2
+delete
All user breakpoints deleted
+loadfile u-boot-socfpga/u-boot
Target Message: Memory access caused precise abort.
Debug Precise Abort Registers : DFSR = 0x00000808, DFAR = 0x01000040
ERROR(CMD16-TAD59-NAL18):
# in ...........u-boot.qspi\a10_soc_devkit_ghrd\software\preloader.ds:32 while executing: loadfile u-boot-socfpga/u-boot
! Failed to load "u-boot"
! Download of 311.088 bytes to address S:0x01000040 failed while writing block of 4.096 bytes to address S:0x01000040
! Bus error on memory operation.
ERROR(CMD656): The script ..........u-boot.qspi\a10_soc_devkit_ghrd\software\preloader.ds failed to complete due to an error during execution of the script "

and also in Terminal the other error is printed :

"

U-Boot SPL 2021.07-16360-gee63370553-dirty (Jan 21 2022 - 08:09:27 +0100)

U-Boot SPL 2021.07-16360-gee63370553-dirty (Jan 21 2022 - 08:09:27 +0100)
Error: Could Not Calibrate SDRAM
DDRCAL: Failed
WDT: Started with servicing (10s timeout)"

I already read most of answers in forums but most of them is for the last version of Quartus which is generate a preloader with BSP editor but in my case I built all with script. 

Is there any solution in this case?