• State Accepted Answer
  • Locked Locked
  • Replies 3 replies
  • Subscribers 16 subscribers
  • Views 9325 views
  • Users 0 members are here
Options
Related
How was your experience today?
This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Save tensorflow model for ArmNN

GeraldK

Hello,

I want to load a Tensorflow model on my ARM-device. The model is rather simple:

Layer (type) Output Shape Param #
=================================================================
conv2d (Conv2D) (None, 1, 32, 8) 120
_________________________________________________________________
re_lu (ReLU) (None, 1, 32, 8) 0
_________________________________________________________________
conv2d_1 (Conv2D) (None, 1, 32, 4) 32
_________________________________________________________________
re_lu_1 (ReLU) (None, 1, 32, 4) 0
_________________________________________________________________
max_pooling2d (MaxPooling2D) (None, 1, 16, 4) 0
_________________________________________________________________
conv2d_2 (Conv2D) (None, 1, 8, 16) 320
_________________________________________________________________
re_lu_2 (ReLU) (None, 1, 8, 16) 0
_________________________________________________________________
conv2d_3 (Conv2D) (None, 1, 8, 8) 128
_________________________________________________________________
re_lu_3 (ReLU) (None, 1, 8, 8) 0
_________________________________________________________________
max_pooling2d_1 (MaxPooling2 (None, 1, 4, 8) 0
_________________________________________________________________
conv2d_4 (Conv2D) (None, 1, 1, 8) 264
_________________________________________________________________
re_lu_4 (ReLU) (None, 1, 1, 8) 0
_________________________________________________________________
conv2d_5 (Conv2D) (None, 1, 1, 2) 18
_________________________________________________________________
flatten (Flatten) (None, 2) 0
=================================================================

I trained the model using Keras + Tesnorflow 1.13.1 and used the same Tensorflow version during the build process of ArmNN. The model is stored in a Keras model file (HDF5) and then converted into an binary Tensorflow model (.pb) using the save_model function.

Unfortunately, I am not able to the model and get the following error message:

'Unsupported operation Max in tensorflow::GraphDef  at function LoadNodeDef [/armnn/armnn-19.02/src/armnnTfParser/TfParser.cpp:3237]'

Since i dont use any uncommon Layers I am a little bit supprised. Loading the MNIST example model (simple_mnist_tf.pb) works fine.

Is their any option i have to pay attention when saving the model? Or is their any documentation about that topic?

Thanks in advance!

Gerald

Parents
  • 0

    Keras inserts extra layers that are sometimes a bit surprising! In this case I would guess the Max layer (not supported by the Arm NN TensorFlow Parser) is used to support some part of the MaxPooling layer (which is supported by the Arm NN TensorFlow Parser).

    In general I would say it's best to export the TF graph to a Tensorflow Lite file, as the tflite_convert utility also cleans up training-only nodes, and does constant-forwarding and certain other optimisations. The file format is a bit more compact as well. Our tflite parser should be able to handle everything you have listed in the model.

Reply
  • 0

    Keras inserts extra layers that are sometimes a bit surprising! In this case I would guess the Max layer (not supported by the Arm NN TensorFlow Parser) is used to support some part of the MaxPooling layer (which is supported by the Arm NN TensorFlow Parser).

    In general I would say it's best to export the TF graph to a Tensorflow Lite file, as the tflite_convert utility also cleans up training-only nodes, and does constant-forwarding and certain other optimisations. The file format is a bit more compact as well. Our tflite parser should be able to handle everything you have listed in the model.

Children
No data