Need timer.h and lcd.h which suits the program given below

"i have the C program for it, but i need Timer.h & Lcd.h for it to work...."

You need the headers to make it Compile - but the headers alone will not make it work.

To make it work you will also need the corresponding source and/or library files.

It is impossible to supply headers without knowing what the corresponding sources and/or libraries are!

And, if you do already have the source and/or library files, you must surely also have the headers?!

"i have the C program for it, but i need Timer.h & Lcd.h for it to work...."

You need the headers to make it Compile - but the headers alone will not make it work.

To make it work you will also need the corresponding source and/or library files.

It is impossible to supply headers without knowing what the corresponding sources and/or libraries are!

And, if you do already have the source and/or library files, you must surely also have the headers?!

i got thz code frm my senior and it works fine in the kit.. they lost the header files and i hav all other codes except the mentioned timer and lcd library files... i just want to edit & put them in the AT89C52

   /* RF id transmitter for vehicle SCHOOL ZONE & HOSPITAL ZONE */
#include <stdio.h>
#include <lcd.h>
#include <timer.h>
PORT: TX_PORT   = P2;
PORT: LCD_PORT  = P0;
PIN: ID_SET_KEY = P1.3;
PIN: IN_A0      = P3.3;
PIN: IN_A1      = P3.4;
unsigned char send_id;
select_id_sw()
{
     if( (IN_A0 == 0) && (IN_A1 == 0 ) )
      {
           uputs(16,0,16,"0:NO ZONE LIMIT ");
           send_id = 0;
       }
     if( (IN_A0 == 1) && (IN_A1 == 0 ) )
       {
          uputs(16,0,16,"1  SCHOOL ZONE  ");
          send_id = 1;
      }
     if( (IN_A0 == 0) && (IN_A1 == 1 ) )
       {
          uputs(16,0,16,"2: HOSPITAL ZONE");
           send_id = 2;
       }
     if( (IN_A0 == 1) && (IN_A1 == 1 ) )
       {
          uputs(16,0,16,"3:NO ZONE LIMIT ");
          send_id = 3;
      }
}
main()
{
 unsigned int d;
  uputs(0,0,16, " VECHILE SPEED  ");
  uputs(16,0,16," ZONE LIMIT TX  ");
  for(d=0; d < 60000; d++);
  for(d=0; d < 60000; d++);
  uputs(0,0,16, " WELCOME TO ECE ");
  uputs(16,0,16,"   DEPARTMENT   ");
  for(d=0; d < 60000; d++);
  for(d=0; d < 60000; d++);
  uputs(0,0,16, "THANKS TO H.O.D ");
  uputs(16,0,16,"  GUIDE & ALL   ");
  for(d=0; d < 60000; d++);
  for(d=0; d < 60000; d++);
  uputs(0,0,16, "   NAME    ");
  uputs(16,0,16,"  NAME   ");
  for(d=0; d < 60000; d++);
  for(d=0; d < 60000; d++);
  uputs(0,0,16, "   NAME    ");
  uputs(16,0,16,"  NAME  ");
  for(d=0; d < 60000; d++);
  for(d=0; d < 60000; d++);
  uputs(0,0,16, "your in setmode ");
  uputs(16,0,16," pls select id  ");
  while(1)
  {
     if( ID_SET_KEY == 0)
       {
           uputs(0,0,16, " u r in setmode ");
         do
          {
            select_id_sw();
          } while(ID_SET_KEY == 0);
         uputs(0,0,16, "VEHICLE ZONE ID ");
         TX_PORT = send_id;
     }
 }
}

PORT: TX_PORT   = P2;
PORT: LCD_PORT  = P0;
PIN: ID_SET_KEY = P1.3;
PIN: IN_A0      = P3.3;
PIN: IN_A1      = P3.4;

This is not Keil syntax - so you must be in the wrong forum!

Even in the right forum, nobody can give you the headers without knowing what the corresponding sources and/or libraries are - and if you have those, you can easily recreate the headers yourself!