[LPC1114] Setting up an SPI interface

Hi, I'm trying to set up an SPI for an LPC1114. I don't have my slave chip just yet, so I just want to be able to read a clk of off PIO0_6, but I'm having a hard time doing this. This is my first time using MCUs in general, so I'm not too comfortable.

For some reason, I can't get any output to display, and I'm not sure what to try anymore. This is the code I have so far:

/* included libraries */
#include <stdio.h>
#include "LPC11xx.h"
//#include "ssp.h"

/* SSP Status register */
#define SSPSR_TFE       (0x1<<0)
#define SSPSR_TNF       (0x1<<1)
#define SSPSR_RNE       (0x1<<2)
#define SSPSR_RFF       (0x1<<3)
#define SSPSR_BSY       (0x1<<4)

/* SSP CR1 register */
#define SSPCR1_LBM      (0x1<<0)
#define SSPCR1_SSE      (0x1<<1)
#define SSPCR1_MS       (0x1<<2)
#define SSPCR1_SOD      (0x1<<3)

/* FIFO Register size */
#define FIFOSIZE        8

/* macro definitions */
#define MY_PIO0_0 0x01
#define MY_PIO0_1 0x02
#define MY_PIO0_2 0x04
#define MY_PIO0_3 0x08
#define MY_PIO0_4 0x10
#define MY_PIO0_5 0x20
#define MY_PIO0_6 0x40
#define MY_PIO0_7 0x80
#define MY_PIO0_8 0x100
#define MY_PIO0_9 0x200

#define CS              0x00
#define SCLK    0x00
#define SDATA   0x00

void config_SSP(void)
{
        uint8_t i, Dummy = Dummy;

        //enable clocks for the SSP
        LPC_SYSCON->PRESETCTRL |= (0x1<<0);
        LPC_SYSCON->SYSAHBCLKCTRL |= (1UL << 11);

        LPC_SYSCON->SSP0CLKDIV = 0xFF; //Orig clk is 3MHz??

        LPC_IOCON->PIO0_8 &= ~0x07; //SSP I/O config
        LPC_IOCON->PIO0_8 |= 0x01; //SSP MISO
        LPC_IOCON->PIO0_9 &= ~0x07;
        LPC_IOCON->PIO0_9 |= 0x01; //SSP MOSI
        LPC_IOCON->SCK_LOC = 0x02;
        LPC_IOCON->PIO0_6 = 0x02;
        LPC_IOCON->PIO0_2 &= ~0x07;
        LPC_IOCON->PIO0_2 |= 0x01;

        //Set DSS data to 8-bit, Frame format SPI, CPOL = 0, CPHA = 0, and SCR is 7
    LPC_SSP0->CR0 = 0x0707;

        //SSPCPSR clock prescale register, master mode, minimum divisor is 0x02
    LPC_SSP0->CPSR = 0x2;

        for(i = 0 ; i < FIFOSIZE ; ++i)
                Dummy = LPC_SSP0->DR;

        //Master mode
    LPC_SSP0->CR1 = 0;
    LPC_SSP0->CR1 = SSPCR1_SSE;
}

void config_GPIO(void)
{
        //enable clocks to GPIO block
        LPC_SYSCON->SYSAHBCLKCTRL |= (1UL <<  6);

        //set port 0_7 to output (high current drain in LPC1114)
    LPC_GPIO0->DIR |= MY_PIO0_7;
}

void SPISend( uint8_t Radd, uint8_t Rval)
{
                        uint8_t Dummy=Dummy;
                Radd&=0x7F;

                /* Move on only if NOT busy and TX FIFO not full. */
                while ( (LPC_SSP1->SR & (SSPSR_TNF|SSPSR_BSY)) != SSPSR_TNF );

                LPC_SSP1->DR = Radd;
                //while ( (LPC_SSP1->SR & (SSPSR_BSY|SSPSR_RNE)) != SSPSR_RNE );
                Dummy = LPC_SSP1->DR;
                                while(!(LPC_SSP0->SR & SSPSR_BSY));
                while ( (LPC_SSP1->SR & (SSPSR_TNF|SSPSR_BSY)) != SSPSR_TNF );

                LPC_SSP1->DR = Rval;
                //while ( (LPC_SSP1->SR & (SSPSR_BSY|SSPSR_RNE)) != SSPSR_RNE );
                                while(!(LPC_SSP0->SR & SSPSR_BSY));
                Dummy = LPC_SSP1->DR;
                return;
}

unsigned char SPIReceive(uint8_t Radd)
{
        unsigned char SPIRECV;
        Radd|=0x80;

        //LPC_GPIO2->MASKED_ACCESS[(1<<SPI_CS)] = (0<<SPI_CS);   // cs=0
        LPC_SSP1->DR = Radd;
        while ( LPC_SSP1->SR & SSPSR_BSY );

        LPC_SSP1->DR = 0xFF;
        while ( (LPC_SSP1->SR & (SSPSR_BSY|SSPSR_RNE)) != SSPSR_RNE );

        SPIRECV = LPC_SSP1->DR;
        return SPIRECV;
}



/* MAIN!!!!!!! */
int main()
{
        int i, j, tmp;

        //init GPIO and SSP
        SystemInit();
        config_GPIO();
        config_SSP();


        while (1)
        {
                SPIReceive((uint8_t)tmp);
                //SPISend(j, j);

                //ledOn();
                for (i = 0; i < 0x0007FFFF; i++)
                {
                }
                //ledOff();
                for (i = 0; i < 0x0007FFFF; i++)
                {
                }
                j++;
        }
}

I really appreciate your help :)