We are running a survey to help us improve the experience for all of our members. If you see the survey appear, please take the time to tell us about your experience if you can.
Hi dazheng,
Need to know ... what is EEPROM used in MCU for ?. I know EEPROM stand for Electrical Erasable Programming ROM but I need to know what's the purpose or where it going to be used in MCU?
I ask this because some of MCU dont have EEPROM ( EEPROM = 0 byte) ie 80NC535 & 80NC321 and the best thing about this MCU (without EEPROM) that's its cheaper than MCU with EEPROM. If it just minor used and can solve it in other method (and not effect my project) , I will use it as I need to lower the cost as much as possible.
Any instruction (ie in proton) that must be used on MCU with EEPROM ?
More explanation greatly appreciated.
Thanks
zuisti
dazheng,
the efkar motor driver circuit is simple but has lots of pins to connect up for the steppering.I had tried a stepper motor controller n driver with L5297 + LR623 and result is perfect.but sometimes it doesnot start and sometimes goes backwards(?) you will use this circuit in the purposed CNC machine.
see home.att.net/.../MD4.html
i think we could make it beter.yes(?)
"backwards(?)"
Yes, good one. A silver star for you.
"i think we could make it beter.yes(?)"
"beter"? No.
"better"? Yes, but no.
In any case, no you couldn't make it better. Even the best CNC machines sometimes don't start. That's just the way they are. CNC motion includes going backwards.
Don't worry.
No improvement needed.
Hi ziusti,
do we we get the 2543b? i think the nmck-45892zr is better(bcoz bigger voltege).
And my proposition is an additional soft-start circuit with an R-LC and an SiAg-diode ...
does you somone have an idea of how to do a control of an induction single phase motor , i ve done one project in my life but it was for three phase, it was depending on the fase angle i think been a long time ive done it, do ou think i can use this priciple with a single phase motor that is monitor the phase via an opto coupler fed to a mcu and the mcu drive an optocouple to drive a triac by pwm?, my pump is is rated 0.5hp my problem is that i have installed a pump for my bathroom and the maximum pressure for my shower heater is 3 bars and my pump is working at 4 bars, the main problem i fear is that the pipes in my shower get damaged quickly and secondly the frequent start of the automatic pump will damage the stator of my motor.
if she goes backward the water is suck up shower; LOL
thanks in advance
"do we we get the 2543b? i think the nmck-45892zr is better(bcoz bigger voltege).
if she goes backward the water is suck up shower; LOL"
"result is perfect. but sometimes it does not start"
This is clearly some new meaning of "perfect" of which we were previously unaware!
That's kind of "perfect in an imperfect sort of way", then?!
I'll tell the QA guys to stop being so negative - everything is "perfect", even if it doesn't work properly!
result is perfect. but sometimes it does not start Maybe they mean "complete" when saying perfect. This would explain why it does not start: It started some time ago and has ended now?
"Maybe they mean 'complete'"
As in, "complete nonsense" - like the rest of the thread...?
I'm dying to see the "machine" these two are trying to conjure up. Apparently it has something to do with an MP3 Player, a bathroom shower, and a CNC machine that is ok if it runs backwards.
This thread has to be a long-winded hoax...there just isn't any way two people can be this stupid!
R
That is what we hope, even if they are quite amusing.
"... a bathroom shower ..."
Plugged up by the very bushy sister that wears only tee-shirts who is such a bad cook that she gives her brother the datashits.
??? why the trollops keep trying to hyjack our project thread ???
i think we must use the secret code to hide detail or they will copy our ideas.
Ive gone back to the playa and want better snd.
I have a pair of unused 5.1 speakers. I was using them with my pc. I want now to use them with my 'television'. The problem to solve is: The speakers have two stereo inputs. One for low frequencies, one for middle rage frequencies and one for hight frequencies.
I want to design an active filter that will be able to split the stereo signal from my 'tv' to this three sections of frequencies.
Many years have passed since I was designing filters and I would like your help. i think we need mcu to do it better with lot more code for better sound. If there is a schematics out there it would be great.
plz.U hv to design active filter according to the frequency response of ur speakers. Then u will get excellent performance from ur filter. I hv one small swollen key filter design software but unable to upload here.
i know it is need for quick. but i know you are good strong profesional guru that helps again.
Thanks mate
... or they will copy our ideas. Hehe.
sorry for disturbing your delopment but i need more help v fat plz.
I also have have a small buzzer that emits many different sounds and, also, 3 error codes:
1) Bip Bip Bip at 440Hz 2) Biiip Biiip Biip at 700Hz 3) Biiiip Biiip Biiiip at 1150Hz 4) Biiiip Bip Biiip Biiiip at 1295Hz
I want to decode these 4 error codes. I can't touch nothing (the buzzer, the amp, the sound) than I must use a small little mic to capture the sound/code.
Besides, the buzzer is situated in a crowded place with many people that speaks, screams, cries etc.
Is it possible to do?
Thanks a lot and sorry, another time.
the buzzer is situated in a crowded place with many people that speaks, screams, cries etc.
Where is this project going to be located?
Sounds like some sort of torture chamber!
A result of the high over-pressure in the showers.
Bip Bip Bip Biiiip Biiiip Biiiip Bip Bip Bip