This discussion has been locked.

You can no longer post new replies to this discussion. If you have a question you can start a new discussion

check the input & ouput of Triscend E5 I/O pin

Hi, can anyone tell me how to
set the input and check the output
of Triscend E5 I/O pins when debugging
in uvision 2? Thanks.

Parents

0 Alex Ruiz over 23 years ago in reply to Andy Neil

Reserved XDATA addresses and non CSL implemented stuff are placed in a TE5_CSOC.H file.

TE5_CSOC.H

* $Id: //depot/software/FC220/include/TE5_CSOC.h#5 $ */
/***************************************************************************
 * Triscend E5 CSoC Device Common Register Definition File
 *
 * This file applies to all members of the Triscend E5 device family.
 *
 * Copyright (c) 2000, 2001 Triscend Corporation. All rights reserved.
 ***************************************************************************
 */

#ifndef _TE5_CSOC_H
#define _TE5_CSOC_H

/***************************************************************************
 * E5 SFR defintions
 ***************************************************************************
 */

/***************************************************************************
 * BYTE Registers
 ***************************************************************************
 */
/* Unused SFR locations [0x80,0xff] are available for use by a soft module. */
//sfr P0    =   0x80;   /* to be exported and implemented in CSL */
sfr SP      =   0x81;
sfr DPL     =   0x82;
sfr DPH     =   0x83;
sfr DPL1    =   0x84;
sfr DPH1    =   0x85;
sfr DPS     =   0x86;
sfr PCON    =   0x87;
sfr TCON    =   0x88;
sfr TMOD    =   0x89;
sfr TL0     =   0x8a;
sfr TL1     =   0x8b;
sfr TH0     =   0x8c;
sfr TH1     =   0x8d;
sfr CKCON   =   0x8e;
/* unused: 0x8f */
//sfr P1    =   0x90;   /* to be exported and implemented in CSL */
/* unused: [0x91,0x97] */
sfr SCON    =   0x98;

...

***************************************************************************
 * E5 Configuration Register Unit (CRU) defintions
 ***************************************************************************
 */

/* All addresses in the range [0xff00,0xffff] are reserved */
#define CMAP0_TAR	(*((unsigned char volatile xdata*) 0xff00))
#define CMAP0_ALT	(*((unsigned char volatile xdata*) 0xff01))
#define CMAP1_TAR_0	(*((unsigned char volatile xdata*) 0xff02))
#define CMAP1_TAR_1	(*((unsigned char volatile xdata*) 0xff03))
...

All your module register declarations will be placed in the <yourprojname>.c file, right after some macro definition.

#ifdef TASKING_TOOLS
#   define SFR_BIT(name,location) _sfrbit name _at( location );
#   define SFR_BYTE(name,location) _sfrbyte name _at( location );
#   define CHAR_XDATA(name,location) volatile unsigned char _xdat name _at( location );
#   define CHAR_ARRAY_XDATA(name,location,size) volatile unsigned char _xdat name[size] _at( location );
#else
#   define SFR_BIT(name,location) sbit name = location;
#   define SFR_BYTE(name,location) sfr name = location;
#   define CHAR_XDATA(name,location) volatile unsigned char xdata name _at_ location;
#   define CHAR_ARRAY_XDATA(name,location,size) volatile unsigned char xdata name[size] _at_ location;
#endif
#define USE_PROJECT_FILE_MACRO

/* add <FastChip install directory>\include to the compiler include path */
#include <TE5_CSOC.h>


// ========= BEGIN SOFT MODULE REGISTER DECLARATIONS ======
    SFR_BYTE (P1,0x90)
// 
//     SELECTOR WITH USER ASSIGNED ADDRESS   
// 

// ========== END SOFT MODULE REGISTER DECLARATIONS =======

FastChip Version 2.3.0 Build 011129-0916

- Alex

Reply

0 Alex Ruiz over 23 years ago in reply to Andy Neil

Reserved XDATA addresses and non CSL implemented stuff are placed in a TE5_CSOC.H file.

TE5_CSOC.H

* $Id: //depot/software/FC220/include/TE5_CSOC.h#5 $ */
/***************************************************************************
 * Triscend E5 CSoC Device Common Register Definition File
 *
 * This file applies to all members of the Triscend E5 device family.
 *
 * Copyright (c) 2000, 2001 Triscend Corporation. All rights reserved.
 ***************************************************************************
 */

#ifndef _TE5_CSOC_H
#define _TE5_CSOC_H

/***************************************************************************
 * E5 SFR defintions
 ***************************************************************************
 */

/***************************************************************************
 * BYTE Registers
 ***************************************************************************
 */
/* Unused SFR locations [0x80,0xff] are available for use by a soft module. */
//sfr P0    =   0x80;   /* to be exported and implemented in CSL */
sfr SP      =   0x81;
sfr DPL     =   0x82;
sfr DPH     =   0x83;
sfr DPL1    =   0x84;
sfr DPH1    =   0x85;
sfr DPS     =   0x86;
sfr PCON    =   0x87;
sfr TCON    =   0x88;
sfr TMOD    =   0x89;
sfr TL0     =   0x8a;
sfr TL1     =   0x8b;
sfr TH0     =   0x8c;
sfr TH1     =   0x8d;
sfr CKCON   =   0x8e;
/* unused: 0x8f */
//sfr P1    =   0x90;   /* to be exported and implemented in CSL */
/* unused: [0x91,0x97] */
sfr SCON    =   0x98;

...

***************************************************************************
 * E5 Configuration Register Unit (CRU) defintions
 ***************************************************************************
 */

/* All addresses in the range [0xff00,0xffff] are reserved */
#define CMAP0_TAR	(*((unsigned char volatile xdata*) 0xff00))
#define CMAP0_ALT	(*((unsigned char volatile xdata*) 0xff01))
#define CMAP1_TAR_0	(*((unsigned char volatile xdata*) 0xff02))
#define CMAP1_TAR_1	(*((unsigned char volatile xdata*) 0xff03))
...

All your module register declarations will be placed in the <yourprojname>.c file, right after some macro definition.

#ifdef TASKING_TOOLS
#   define SFR_BIT(name,location) _sfrbit name _at( location );
#   define SFR_BYTE(name,location) _sfrbyte name _at( location );
#   define CHAR_XDATA(name,location) volatile unsigned char _xdat name _at( location );
#   define CHAR_ARRAY_XDATA(name,location,size) volatile unsigned char _xdat name[size] _at( location );
#else
#   define SFR_BIT(name,location) sbit name = location;
#   define SFR_BYTE(name,location) sfr name = location;
#   define CHAR_XDATA(name,location) volatile unsigned char xdata name _at_ location;
#   define CHAR_ARRAY_XDATA(name,location,size) volatile unsigned char xdata name[size] _at_ location;
#endif
#define USE_PROJECT_FILE_MACRO

/* add <FastChip install directory>\include to the compiler include path */
#include <TE5_CSOC.h>


// ========= BEGIN SOFT MODULE REGISTER DECLARATIONS ======
    SFR_BYTE (P1,0x90)
// 
//     SELECTOR WITH USER ASSIGNED ADDRESS   
// 

// ========== END SOFT MODULE REGISTER DECLARATIONS =======

FastChip Version 2.3.0 Build 011129-0916

- Alex

Children

0 Minkui Liu over 23 years ago in reply to Alex Ruiz

Thx all for your inputs.I really
appreciate it. Again, sincere thanks
to all.
Cancel
Vote up 0 Vote down

Cancel