• State Not Answered
  • Locked Locked
  • Replies 3 replies
  • Subscribers 351 subscribers
  • Views 3397 views
  • Users 0 members are here
2025 survey

We are running a survey to help us improve the experience for all of our members. If you see the survey appear, please take the time to tell us about your experience if you can.

Options
Related
How was your experience today?
This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Help to debug boot issue

eric976

Hello

I have done a custom PCB based on Olinuxino open-source hardware. I'm having the following messages when I'm trying to boot, can someone help me to identify how to solve this?

U-Boot SPL 2021.04+olimex-1-20211108.075936 (Nov 08 2021 - 08:00:41 +0000)
DRAM: 2048 MiB
Trying to boot from MMC1
ASSERT: lib/xlat_tables_v2/xlat_tables_core.c:1150
BACKTRACE: START: assert
0: EL3: 0x48910
1: EL3: 0x4bd24
2: EL3: 0x4985c
3: EL3: 0x49964
4: EL3: 0x440bc
5: EL3: 0x11fac
6: EL3: 0x1189c
BACKTRACE: END: assert

Thanks in advance.

Parents
  • 0 in reply to Zhifei Yang

    Hello

    Thanks for your reply. I already managed how to go further, but now I'm stopping in "kernel BUG at arch/arm64/kernel/traps.c:407!". Is this related to what? Kernel? Root file system? Any advice please...

    HELLO! BOOT0 is starting!------!-!
    boot0 commit : 8
    boot0 version : 4.0.0
    set pll start
    set pll end
    rtc[0] value = 0x00000000
    rtc[1] value = 0x00000000
    rtc[2] value = 0x00000000
    rtc[3] value = 0x00000000
    rtc[4] value = 0x00000000
    rtc[5] value = 0x00000000
    DRAM driver version: V1.0
    DRAM Type = 3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
    DRAM clk = 672 MHz
    DRAM zq value: 003b3bbb
    rsb_send_initseq: rsb clk 400Khz -> 3Mhz
    PMU: AXP81X
    ddr voltage = 1500 mv
    DRAM dual rank full DQ gate training OK
    DRAM size = 2048 MB
    DRAM init ok
    dram size =2048
    card boot number = 0, boot0 copy = 0
    card no is 0
    sdcard 0 line count 4
    [mmc]: mmc driver ver 2015-05-08 20:06
    [mmc]: sdc0 spd mode error, 2
    [mmc]: Wrong media type 0x00000000
    [mmc]: ***Try SD card 0***
    [mmc]: HSSDR52/SDR25 4 bit
    [mmc]: 50000000 Hz
    [mmc]: 15193 MB
    [mmc]: ***SD/MMC 0 init OK!!!***
    sdcard 0 init ok
    The size of uboot is 000f0000.
    sum=9373abea
    src_sum=9373abea
    Succeed in loading uboot from sdmmc flash.
    boot0: start load other image
    boot0: Loading BL3-1
    Loading file 0 at address 0x40000000,size 0x0000b400 success
    boot0: Loading scp
    Loading file 2 at address 0x00040000,size 0x00019c00 success
    set arisc reset to de-assert state
    Ready to disable icache.
    J9=▒ Configuring SPC Controller
    NOTICE: BL3-1: v1.0(debug):0bc348a
    NOTICE: BL3-1: Built : 01:16:30, Jan 4 2017
    NOTICE: BL3-1 commit: 0bc348ab272ad81a4faf128ef38f4724f36fded6

    INFO: BL3-1: Initializing runtime services
    INFO: BL3-1: Preparing for EL3 exit to normal world
    INFO: BL3-1: Next image address = 0x4a000000
    INFO: BL3-1: Next image spsr = 0x1d3


    U-Boot 2014.07-4-pine64-gf38a9d4 (Nov 23 2021 - 06:21:41) Allwinner Technology

    uboot commit : f38a9d42a764cb9c1afa31ea0bc9757bbff901e4

    rsb: secure monitor exist
    [ 0.388]pmbus: ready
    [ 0.391][ARISC] :arisc initialize
    [ 0.826][ARISC] :arisc_dvfs_cfg_vf_table: support only one vf_table
    [SCP] :sunxi-arisc driver begin startup 2
    [SCP] :arisc_para size:1a8
    [SCP] :arisc version: [v0.1.76]
    [SCP] :sunxi-arisc driver v1.10 is starting
    [ 0.987][ARISC] :sunxi-arisc driver startup succeeded
    [ 1.032]PMU: AXP81X
    [ 1.034]PMU: AXP81X found
    bat_vol=1091, ratio=100
    [ 1.041]PMU: dcdc2 1100
    [ 1.044]PMU: cpux 1008 Mhz,AXI=336 Mhz
    PLL6=600 Mhz,AHB1=200 Mhz, APB1=100Mhz AHB2=300Mhz MBus=400Mhz
    device_type = 3253, onoff=1
    dcdc1_vol = 3300, onoff=1
    dcdc2_vol = 1100, onoff=1
    dcdc6_vol = 1100, onoff=1
    aldo1_vol = 3300, onoff=1
    aldo2_vol = 1800, onoff=1
    aldo3_vol = 3000, onoff=1
    dldo1_vol = 3300, onoff=0
    dldo2_vol = 3300, onoff=0
    dldo3_vol = 2800, onoff=0
    dldo4_vol = 3300, onoff=1
    eldo1_vol = 1800, onoff=1
    eldo2_vol = 1800, onoff=0
    eldo3_vol = 1800, onoff=0
    fldo1_vol = 1200, onoff=0
    fldo2_vol = 1100, onoff=1
    gpio0_vol = 3100, onoff=0
    gpio1_vol = 3100, onoff=0
    vbus not exist
    no battery, limit to dc
    run key detect
    no key found
    no uart input
    DRAM: 2 GiB
    fdt addr: 0xb6eba640
    Relocation Offset is: 75f0c000
    In: serial
    Out: serial
    Err: serial
    gic: sec monitor mode
    [ 1.892]start
    drv_disp_init
    init_clocks: finish init_clocks.
    enable power vcc-hdmi-33, ret=0
    drv_disp_init finish
    boot_disp.output_disp=0
    boot_disp.output_type=3
    boot_disp.output_mode=10
    fetch script data boot_disp.auto_hpd fail
    disp0 device type(4) enable
    attched ok, mgr0<-->device1, type=4, mode=10
    [ 2.561]end
    workmode = 0,storage type = 1
    [ 2.566]MMC: 0
    [mmc]: mmc driver ver 2015-06-03 13:50:00
    SUNXI SD/MMC: 0
    [mmc]: start mmc_calibrate_delay_unit, don't access device...
    [mmc]: delay chain cal done, sample: 200(ps)
    [mmc]: media type 0x0
    [mmc]: Wrong media type 0x0
    [mmc]: ************Try SD card 0************
    [mmc]: host caps: 0x27
    [mmc]: MID 03 PSN 379f237a
    [mmc]: PNM SC16G -- 0x53-43-31-36-47
    [mmc]: PRV 8.0
    [mmc]: MDT m-7 y-2019
    [mmc]: speed mode : HSSDR52/SDR25
    [mmc]: clock : 50000000 Hz
    [mmc]: bus_width : 4 bit
    [mmc]: user capacity : 15193 MB
    [mmc]: ************SD/MMC 0 init OK!!!************
    [mmc]: erase_grp_size : 0x1WrBlk*0x200=0x200 Byte
    [mmc]: secure_feature : 0x0
    [mmc]: secure_removal_type : 0x0
    [ 2.931]sunxi flash init ok
    [mmc]: Has init
    [ 3.018]---drivers/mmc/mmc.c 2733 mmc_init
    reading uboot.env
    FAT: Misaligned buffer address (b6e945e8)
    --------fastboot partitions--------
    mbr not exist
    base bootcmd=run mmcbootcmd
    bootcmd set setargs_mmc
    key 0
    recovery key high 12, low 10
    fastboot key high 6, low 4
    no misc partition is found
    to be run cmd=run mmcbootcmd
    update dtb dram start
    update dtb dram end
    serial is: 340078f4c71c34100ad0
    Model: a64-olinuxino
    no battery exist
    sunxi_bmp_logo_display
    [mmc]: Has init
    [ 3.615]---drivers/mmc/mmc.c 2733 mmc_init
    reading bootlogo.bmp
    3148922 bytes read in 160 ms (18.8 MiB/s)
    bmp file buffer: 0x41000000, bmp_info.buffer: 47400000
    fetch script data boot_disp.output_full fail
    screen_id =0, screen_width =1920, screen_height =1080
    frame buffer address 47400036
    [ 4.673]inter uboot shell
    Hit any key to stop autoboot: 0
    [mmc]: Has init
    [ 7.930]---drivers/mmc/mmc.c 2733 mmc_init
    reading uEnv.txt
    [mmc]: blkcnt should not be 0
    118 bytes read in 5 ms (22.5 KiB/s)
    Loading boot environment ...
    [mmc]: Has init
    [ 7.952]---drivers/mmc/mmc.c 2733 mmc_init
    reading boot.scr
    ** Unable to read file boot.scr **
    Booting with defaults ...
    [mmc]: Has init
    [ 7.972]---drivers/mmc/mmc.c 2733 mmc_init
    reading a64/a64-olinuxino.dtb
    67677 bytes read in 8 ms (8.1 MiB/s)
    [mmc]: Has init
    [ 8.028]---drivers/mmc/mmc.c 2733 mmc_init
    reading a64/Image
    19787784 bytes read in 985 ms (19.2 MiB/s)
    [mmc]: Has init
    [ 9.027]---drivers/mmc/mmc.c 2733 mmc_init
    reading initrd.gz
    1104262 bytes read in 57 ms (18.5 MiB/s)
    ## Flattened Device Tree blob at 45000000
    Booting using the fdt blob at 0x45000000
    reserving fdt memory region: addr=41010000 size=10000
    reserving fdt memory region: addr=41020000 size=800
    reserving fdt memory region: addr=40100000 size=4000
    reserving fdt memory region: addr=40104000 size=1000
    reserving fdt memory region: addr=40105000 size=1000
    reserving fdt memory region: addr=45000000 size=11000
    Loading Ramdisk to b6da5000, end b6eb2986 ... OK
    Loading Device Tree to 44feb000, end 44ffefff ... OK

    Starting kernel ...

    [mmc]: MMC Device 2 not found
    [mmc]: mmc 2 not find, so not exit
    INFO: BL3-1: Next image address = 0x41000000
    INFO: BL3-1: Next image spsr = 0x3c5
    [ 0.000000] Internal error: Oops - BUG: 0 [#1] SMP
    [ 0.000000] Modules linked in:
    [ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 5.10.60 #1
    [ 0.000000] Hardware name: sun50iw1p1 (DT)
    [ 0.000000] pstate: 00000085 (nzcv daIf -PAN -UAO -TCO BTYPE=--)
    [ 0.000000] pc : do_undefinstr+0x358/0x378
    [ 0.000000] lr : do_undefinstr+0x270/0x378
    [ 0.000000] sp : ffff800011133cc0
    [ 0.000000] x29: ffff800011133cc0 x28: ffff800011141640
    [ 0.000000] x27: ffff800010c2ff60 x26: ffff800010c5f930
    [ 0.000000] x25: 0000000000000003 x24: ffffff00ff000000
    [ 0.000000] x23: 0000000040000085 x22: ffff8000100104f0
    [ 0.000000] x21: ffff800011133ea0 x20: ffff800011141640
    [ 0.000000] x19: ffff800011133d50 x18: 0000000000000001
    [ 0.000000] x17: 0000000000000000 x16: 0000000000000000
    [ 0.000000] x15: ffffffffffffffff x14: ffffffffff000000
    [ 0.000000] x13: ffffffffffffffff x12: 0000000000000018
    [ 0.000000] x11: 0000000000000020 x10: 0101010101010101
    [ 0.000000] x9 : fffffffffffffffe x8 : 7f7f7f7f7f7f7f7f
    [ 0.000000] x7 : fefefeff6862726f x6 : ffff800011133d18
    [ 0.000000] x5 : 0000000000000000 x4 : ffff8000112e4110
    [ 0.000000] x3 : 0000000000000000 x2 : ffff8000111435a8
    [ 0.000000] x1 : ffff8000112e4110 x0 : 0000000040000085
    [ 0.000000] Call trace:
    [ 0.000000] do_undefinstr+0x358/0x378
    [ 0.000000] el1_undef+0x30/0x50
    [ 0.000000] el1_sync_handler+0x8c/0xc8
    [ 0.000000] el1_sync+0x88/0x140
    [ 0.000000] get_cpu_ops+0x0/0x20
    [ 0.000000] setup_arch+0x414/0x594
    [ 0.000000] start_kernel+0x80/0x534
    [ 0.000000] ------------[ cut here ]------------
    [ 0.000000] kernel BUG at arch/arm64/kernel/traps.c:407!

Reply
  • 0 in reply to Zhifei Yang

    Hello

    Thanks for your reply. I already managed how to go further, but now I'm stopping in "kernel BUG at arch/arm64/kernel/traps.c:407!". Is this related to what? Kernel? Root file system? Any advice please...

    HELLO! BOOT0 is starting!------!-!
    boot0 commit : 8
    boot0 version : 4.0.0
    set pll start
    set pll end
    rtc[0] value = 0x00000000
    rtc[1] value = 0x00000000
    rtc[2] value = 0x00000000
    rtc[3] value = 0x00000000
    rtc[4] value = 0x00000000
    rtc[5] value = 0x00000000
    DRAM driver version: V1.0
    DRAM Type = 3 (2:DDR2,3:DDR3,6:LPDDR2,7:LPDDR3)
    DRAM clk = 672 MHz
    DRAM zq value: 003b3bbb
    rsb_send_initseq: rsb clk 400Khz -> 3Mhz
    PMU: AXP81X
    ddr voltage = 1500 mv
    DRAM dual rank full DQ gate training OK
    DRAM size = 2048 MB
    DRAM init ok
    dram size =2048
    card boot number = 0, boot0 copy = 0
    card no is 0
    sdcard 0 line count 4
    [mmc]: mmc driver ver 2015-05-08 20:06
    [mmc]: sdc0 spd mode error, 2
    [mmc]: Wrong media type 0x00000000
    [mmc]: ***Try SD card 0***
    [mmc]: HSSDR52/SDR25 4 bit
    [mmc]: 50000000 Hz
    [mmc]: 15193 MB
    [mmc]: ***SD/MMC 0 init OK!!!***
    sdcard 0 init ok
    The size of uboot is 000f0000.
    sum=9373abea
    src_sum=9373abea
    Succeed in loading uboot from sdmmc flash.
    boot0: start load other image
    boot0: Loading BL3-1
    Loading file 0 at address 0x40000000,size 0x0000b400 success
    boot0: Loading scp
    Loading file 2 at address 0x00040000,size 0x00019c00 success
    set arisc reset to de-assert state
    Ready to disable icache.
    J9=▒ Configuring SPC Controller
    NOTICE: BL3-1: v1.0(debug):0bc348a
    NOTICE: BL3-1: Built : 01:16:30, Jan 4 2017
    NOTICE: BL3-1 commit: 0bc348ab272ad81a4faf128ef38f4724f36fded6

    INFO: BL3-1: Initializing runtime services
    INFO: BL3-1: Preparing for EL3 exit to normal world
    INFO: BL3-1: Next image address = 0x4a000000
    INFO: BL3-1: Next image spsr = 0x1d3


    U-Boot 2014.07-4-pine64-gf38a9d4 (Nov 23 2021 - 06:21:41) Allwinner Technology

    uboot commit : f38a9d42a764cb9c1afa31ea0bc9757bbff901e4

    rsb: secure monitor exist
    [ 0.388]pmbus: ready
    [ 0.391][ARISC] :arisc initialize
    [ 0.826][ARISC] :arisc_dvfs_cfg_vf_table: support only one vf_table
    [SCP] :sunxi-arisc driver begin startup 2
    [SCP] :arisc_para size:1a8
    [SCP] :arisc version: [v0.1.76]
    [SCP] :sunxi-arisc driver v1.10 is starting
    [ 0.987][ARISC] :sunxi-arisc driver startup succeeded
    [ 1.032]PMU: AXP81X
    [ 1.034]PMU: AXP81X found
    bat_vol=1091, ratio=100
    [ 1.041]PMU: dcdc2 1100
    [ 1.044]PMU: cpux 1008 Mhz,AXI=336 Mhz
    PLL6=600 Mhz,AHB1=200 Mhz, APB1=100Mhz AHB2=300Mhz MBus=400Mhz
    device_type = 3253, onoff=1
    dcdc1_vol = 3300, onoff=1
    dcdc2_vol = 1100, onoff=1
    dcdc6_vol = 1100, onoff=1
    aldo1_vol = 3300, onoff=1
    aldo2_vol = 1800, onoff=1
    aldo3_vol = 3000, onoff=1
    dldo1_vol = 3300, onoff=0
    dldo2_vol = 3300, onoff=0
    dldo3_vol = 2800, onoff=0
    dldo4_vol = 3300, onoff=1
    eldo1_vol = 1800, onoff=1
    eldo2_vol = 1800, onoff=0
    eldo3_vol = 1800, onoff=0
    fldo1_vol = 1200, onoff=0
    fldo2_vol = 1100, onoff=1
    gpio0_vol = 3100, onoff=0
    gpio1_vol = 3100, onoff=0
    vbus not exist
    no battery, limit to dc
    run key detect
    no key found
    no uart input
    DRAM: 2 GiB
    fdt addr: 0xb6eba640
    Relocation Offset is: 75f0c000
    In: serial
    Out: serial
    Err: serial
    gic: sec monitor mode
    [ 1.892]start
    drv_disp_init
    init_clocks: finish init_clocks.
    enable power vcc-hdmi-33, ret=0
    drv_disp_init finish
    boot_disp.output_disp=0
    boot_disp.output_type=3
    boot_disp.output_mode=10
    fetch script data boot_disp.auto_hpd fail
    disp0 device type(4) enable
    attched ok, mgr0<-->device1, type=4, mode=10
    [ 2.561]end
    workmode = 0,storage type = 1
    [ 2.566]MMC: 0
    [mmc]: mmc driver ver 2015-06-03 13:50:00
    SUNXI SD/MMC: 0
    [mmc]: start mmc_calibrate_delay_unit, don't access device...
    [mmc]: delay chain cal done, sample: 200(ps)
    [mmc]: media type 0x0
    [mmc]: Wrong media type 0x0
    [mmc]: ************Try SD card 0************
    [mmc]: host caps: 0x27
    [mmc]: MID 03 PSN 379f237a
    [mmc]: PNM SC16G -- 0x53-43-31-36-47
    [mmc]: PRV 8.0
    [mmc]: MDT m-7 y-2019
    [mmc]: speed mode : HSSDR52/SDR25
    [mmc]: clock : 50000000 Hz
    [mmc]: bus_width : 4 bit
    [mmc]: user capacity : 15193 MB
    [mmc]: ************SD/MMC 0 init OK!!!************
    [mmc]: erase_grp_size : 0x1WrBlk*0x200=0x200 Byte
    [mmc]: secure_feature : 0x0
    [mmc]: secure_removal_type : 0x0
    [ 2.931]sunxi flash init ok
    [mmc]: Has init
    [ 3.018]---drivers/mmc/mmc.c 2733 mmc_init
    reading uboot.env
    FAT: Misaligned buffer address (b6e945e8)
    --------fastboot partitions--------
    mbr not exist
    base bootcmd=run mmcbootcmd
    bootcmd set setargs_mmc
    key 0
    recovery key high 12, low 10
    fastboot key high 6, low 4
    no misc partition is found
    to be run cmd=run mmcbootcmd
    update dtb dram start
    update dtb dram end
    serial is: 340078f4c71c34100ad0
    Model: a64-olinuxino
    no battery exist
    sunxi_bmp_logo_display
    [mmc]: Has init
    [ 3.615]---drivers/mmc/mmc.c 2733 mmc_init
    reading bootlogo.bmp
    3148922 bytes read in 160 ms (18.8 MiB/s)
    bmp file buffer: 0x41000000, bmp_info.buffer: 47400000
    fetch script data boot_disp.output_full fail
    screen_id =0, screen_width =1920, screen_height =1080
    frame buffer address 47400036
    [ 4.673]inter uboot shell
    Hit any key to stop autoboot: 0
    [mmc]: Has init
    [ 7.930]---drivers/mmc/mmc.c 2733 mmc_init
    reading uEnv.txt
    [mmc]: blkcnt should not be 0
    118 bytes read in 5 ms (22.5 KiB/s)
    Loading boot environment ...
    [mmc]: Has init
    [ 7.952]---drivers/mmc/mmc.c 2733 mmc_init
    reading boot.scr
    ** Unable to read file boot.scr **
    Booting with defaults ...
    [mmc]: Has init
    [ 7.972]---drivers/mmc/mmc.c 2733 mmc_init
    reading a64/a64-olinuxino.dtb
    67677 bytes read in 8 ms (8.1 MiB/s)
    [mmc]: Has init
    [ 8.028]---drivers/mmc/mmc.c 2733 mmc_init
    reading a64/Image
    19787784 bytes read in 985 ms (19.2 MiB/s)
    [mmc]: Has init
    [ 9.027]---drivers/mmc/mmc.c 2733 mmc_init
    reading initrd.gz
    1104262 bytes read in 57 ms (18.5 MiB/s)
    ## Flattened Device Tree blob at 45000000
    Booting using the fdt blob at 0x45000000
    reserving fdt memory region: addr=41010000 size=10000
    reserving fdt memory region: addr=41020000 size=800
    reserving fdt memory region: addr=40100000 size=4000
    reserving fdt memory region: addr=40104000 size=1000
    reserving fdt memory region: addr=40105000 size=1000
    reserving fdt memory region: addr=45000000 size=11000
    Loading Ramdisk to b6da5000, end b6eb2986 ... OK
    Loading Device Tree to 44feb000, end 44ffefff ... OK

    Starting kernel ...

    [mmc]: MMC Device 2 not found
    [mmc]: mmc 2 not find, so not exit
    INFO: BL3-1: Next image address = 0x41000000
    INFO: BL3-1: Next image spsr = 0x3c5
    [ 0.000000] Internal error: Oops - BUG: 0 [#1] SMP
    [ 0.000000] Modules linked in:
    [ 0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted 5.10.60 #1
    [ 0.000000] Hardware name: sun50iw1p1 (DT)
    [ 0.000000] pstate: 00000085 (nzcv daIf -PAN -UAO -TCO BTYPE=--)
    [ 0.000000] pc : do_undefinstr+0x358/0x378
    [ 0.000000] lr : do_undefinstr+0x270/0x378
    [ 0.000000] sp : ffff800011133cc0
    [ 0.000000] x29: ffff800011133cc0 x28: ffff800011141640
    [ 0.000000] x27: ffff800010c2ff60 x26: ffff800010c5f930
    [ 0.000000] x25: 0000000000000003 x24: ffffff00ff000000
    [ 0.000000] x23: 0000000040000085 x22: ffff8000100104f0
    [ 0.000000] x21: ffff800011133ea0 x20: ffff800011141640
    [ 0.000000] x19: ffff800011133d50 x18: 0000000000000001
    [ 0.000000] x17: 0000000000000000 x16: 0000000000000000
    [ 0.000000] x15: ffffffffffffffff x14: ffffffffff000000
    [ 0.000000] x13: ffffffffffffffff x12: 0000000000000018
    [ 0.000000] x11: 0000000000000020 x10: 0101010101010101
    [ 0.000000] x9 : fffffffffffffffe x8 : 7f7f7f7f7f7f7f7f
    [ 0.000000] x7 : fefefeff6862726f x6 : ffff800011133d18
    [ 0.000000] x5 : 0000000000000000 x4 : ffff8000112e4110
    [ 0.000000] x3 : 0000000000000000 x2 : ffff8000111435a8
    [ 0.000000] x1 : ffff8000112e4110 x0 : 0000000040000085
    [ 0.000000] Call trace:
    [ 0.000000] do_undefinstr+0x358/0x378
    [ 0.000000] el1_undef+0x30/0x50
    [ 0.000000] el1_sync_handler+0x8c/0xc8
    [ 0.000000] el1_sync+0x88/0x140
    [ 0.000000] get_cpu_ops+0x0/0x20
    [ 0.000000] setup_arch+0x414/0x594
    [ 0.000000] start_kernel+0x80/0x534
    [ 0.000000] ------------[ cut here ]------------
    [ 0.000000] kernel BUG at arch/arm64/kernel/traps.c:407!

Children
  • 0 Arm Employee Badge in reply to eric976

    It is weird that after "starting kernel...", the code execution flow shows "INFO: BL3-1: Next image address = 0x41000000
    INFO: BL3-1: Next image spsr = 0x3c5".  From u-boot, you should configure and jump to Linux kernel address, but you jumps the BL31 wrongly or at least BL31 entry point overlaps part of your kernel memory.