This discussion has been locked.

You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Morello board, no output on AP port

I have a new morello board that I'm trying to get setup. I've followed the setup instructions and have the USB debug line connected to a Linux host (in VMWare).

Upon power on, I get serial output on the MCC, PCC, SCP and MCP lines but all the other lines are blank including the AP line. I've attached the output I get.

I was able to update the firmware SD card and saw the MCC copy it over but no change. Its like its stuck waiting for a signal but I don't know what. NOTE: I do have a bootable image on the SATA drive and on a USB drive connected to the box.

MCC


Arm M1SDP MCC Boot loader v1.0.0
HBI0364 build 641

MCC: Power On

MCC to access SD card request acknowledged.
Clear ULINK JTAG

Time :  07:09:58 
Date :  09:11:2023 

Arm M1SDP MCC Firmware v2.3.3
Build Date: Jun 23 2023

Powering up system...

MCC to access SD card request acknowledged.
Clear ULINK JTAG

Time :  07:10:05 
Date :  09:11:2023 

Switching on ATXPSU...
Switching on main power...

12V Rail Check Pass

Reading Board File \MB\HBI0364B\io_v010f.txt
TOTAL OSCCLKS: 15
PMIC RAM configuration (80_1_86G.bin)...

Temperature (deg C)
Outlet = 24.2 PMIC   = 28.2 SoC = 27.9 IN2  = 26.1 IN1 = 24.3 
MidBrd = 28   PCIeSW = 25   MCC = 25.4 FPGA = 27.5 SoC Fan Speed = 9%
ALERT off

Configuring motherboard (rev B, var A)...

Configuring FPGA from file \MB\HBI0364B\io_v010f.bit
Address: 0x00000000Address: 0x00020000Address: 0x00040000Address: 0x00060000Address: 0x00080000Address: 0x000A0000Address: 0x000C0000Address: 0x000E0000Address: 0x00100000Address: 0x00120000Address: 0x00140000Address: 0x00160000Address: 0x00180000Address: 0x001A0000Address: 0x001C0000Address: 0x001E0000Address: 0x00200000Address: 0x00220000Address: 0x00240000Address: 0x00260000Address: 0x00280000Address: 0x002A0000Address: 0x002C0000Address: 0x002E0000Address: 0x00300000Address: 0x00320000Address: 0x00340000Address: 0x00360000Address: 0x00380000Address: 0x003A0000Address: 0x003C0000Address: 0x003E0000Address: 0x00400000Address: 0x00420000Address: 0x00440000Address: 0x00460000Address: 0x00480000Address: 0x004A0000Address: 0x004C0000Address: 0x004E0000Address: 0x00500000Address: 0x00520000Address: 0x00540000Address: 0x00560000Address: 0x00580000Address: 0x005A0000Address: 0x005C0000Address: 0x005E0000Address: 0x00600000Address: 0x00620000Address: 0x00640000Address: 0x00660000Address: 0x00680000Address: 0x006A0000Address: 0x006C0000Address: 0x006E0000Address: 0x00700000Address: 0x00720000Address: 0x00740000Address: 0x00760000Address: 0x00780000Address: 0x007A0000Address: 0x007C0000Address: 0x007E0000
FPGA configuration complete.

Config clocks num: 15
OSCCLK0  : 50.000000MHz
OSCCLK1  : 50.000000MHz
OSCCLK2  : 50.000000MHz
OSCCLK3  : 50.000000MHz
OSCCLK4  : 50.000000MHz
OSCCLK5  : 50.000000MHz
OSCCLK6  : 50.000000MHz
OSCCLK7  : 50.000000MHz
OSCCLK8  : 75.000000MHz
OSCCLK9  : 85.000000MHz
OSCCLK10  : 12.288000MHz
OSCCLK11  : 50.000000MHz
OSCCLK12  : 50.000000MHz
OSCCLK13  : 50.000000MHz
OSCCLK14  : 170.000000MHz
OSCCLK setup: PASSED
GTXCLK setup: PASSED

EEPROM config found
File to compare \MB\HBI0364B\pci_v002.bin \MB\HBI0364B\pci_v002.bin
Writing SCC 0x014 with ACLK 50000000 Hz
Writing SCC 0x00C with 0x00000003
Writing SCC 0x020 with 0x06090805
Writing SCC 0x024 with 0x06060606
Writing SCC 0x028 with 0x00000606
Writing SCC 0x1160 with 0x00000001
Writing SCC 0x1164 with 0x01000000
Writing SCC 0x1168 with 0x00000000
Writing SCC 0x116C with 0x00000000
Writing SCC 0x1180 with 0x00000000
Writing SCC 0x1184 with 0x0000000C
Writing SCC 0x1188 with 0x00000000
Writing SCC 0x118C with 0x00000000
Writing SCC 0x1190 with 0x00000000
Writing SCC 0x1194 with 0x00000000
Writing SCC 0x1198 with 0x00000000
Writing SCC 0x119C with 0x00000000
Reading SCC 0xFF8 with 0x0A364A08
Reading SCC 0xFFC with 0x41050000

QSPI Controller detected id = 0x4000303
Device ID 0x20, 0xBB, 0x19
Setting QSPI dummy clocks...
Dummy clocks already set
Device ID 0x20, 0xBB, 0x19
QSPI Controller detected id = 0x4000303
Device ID 0x20, 0xBB, 0x19
Setting QSPI dummy clocks...
Dummy clocks already set
Device ID 0x20, 0xBB, 0x19
QSPI Controller detected id = 0x4000303
Device ID 0x20, 0xBB, 0x19
Setting QSPI dummy clocks...
Dummy clocks already set
Device ID 0x20, 0xBB, 0x19

Reading images file \MB\HBI0364B\images.txt

PCIe NIC MAC address = 0002 F7009B29
PCC MAC address = 0002 F7009B28
LAN9221 was identified successfully.
MAC addrs test: PASSED

SMC MAC address 0002-F700-9B2A

Identifying DDR 0

Device Information
Manufacturer ID = 80 2C
Module Part Number = 9ASF1G72PZ-2G9E1    
Module Serial Number = 30 7A A1 7

Identifying DDR 1

Device Information
Manufacturer ID = 80 2C
Module Part Number = 9ASF1G72PZ-2G9E1    
Module Serial Number = 30 7A 87 2F

Setting System LEDs[7:4]
Setting PCIe_nPERST/PCIESW_PERSTN
PCIe control C2C disabled
APUART0 connected to USBPORT_3
SCPUART connected to USBPORT_4
MCPUART connected to USBPORT_5
PL031 Date & Time set = Thu Nov  9 07:10:24 2023

QSPI test (0x6403FEF8):0xFFFFFFFF
Releasing SOC_nPOR/SOC_nSRST
Setting I2C_MUX to SCP
USB Serial Number = 50053022C034
Cmd>

PCC


Arm M1SDP PCC Boot loader v1.0.3
Starting the PCC Bios...


 ___   ___   ___
| _ \ /  _| /  _|
|  _/ | (_  | (_
|_|   \___| \___|
ARM Platform Configuration Controller Firmware
Platform: Morello
Configuration: Morello
Build Date: Wed Aug 24 20:39:36 BST 2022
Build Version: PCC_v056
Copyright 2018-22 ARM Limited
ALL RIGHTS RESERVED.
LED init...SUCCESS
IOFPGA FMC memory mapping init...SUCCESS
No startup options installed, skipping countdown.
EEPROM init...SUCCESS
RTC init...SUCCESS
Initializing SPI1 interface to MCC.
Initializing SPI interface 0
SPI interface 1 clock is enabled.
SPI interface 0 is enabled.
MCC SPI1 IRQs enabled.
MCC SPI Interface HW setup completed.
MCC SPI Interface setup completed.
PCC2SCP interface init...SUCCESS
Initializing module with index 0
Initializing module with index 1
Initializing module with index 2
Firmware Services Initialization Complete.
PCC SPI1 timer initialization finished.
pcc_cli>[ETH] MAC address: 00:02:F7:00:9B:28
[ETH] HAL_ETH_Init failed!
[ETH] Link down, check ethernet connection.
IPMI listener active.
Received reset request from SoC via F2P_SS_RSTREQ.
F2P_SS_RSTREQ ignored because IOFPGA is powered off.
F2PCC_INT triggered by IOFPGA, nothing to do here.
Sent reg 2000   cmd 0000   data 0000
Received reg D003   cmd 0000   data 0002
MCC Request Command detected
PCC FMC GPIO init request
PCC FMC GPIO init complete

SCP

[    0.000000]  ___  ___ ___      __ _
[    0.000000] / __|/ __| _ \___ / _(_)_ _ _ ____ __ ____ _ _ _ ___
[    0.000000] \__ | (__|  _|___|  _| | '_| '  \ V  V / _` | '_/ -_)
[    0.000000] |___/\___|_|     |_| |_|_| |_|_|_\_/\_/\__,_|_| \___|
[    0.000000] 
[    0.000000] v2.7.0_2020-11-19_07-20-34-d49e1335
[    0.000000] 
[    0.000000] [FWK] Module initialization complete!
[    0.000000] [ROM] Trying to identify FIP at 0x30000000
[    0.000000] [ROM] Located SCP_BL2:
[    0.000000] [ROM]   address: 0x30000060
[    0.000000] [ROM]   size   : 172880
[    0.000000] [ROM]   flags  : 0x0000000000000000
[    0.000000] [ROM] Copying SCP_BL2 to ITCRAM...!
[    0.000000] [ROM] Done!
[    0.000000] [ROM] Jumping to SCP_BL2
[    0.000000]  ___  ___ ___      __ _
[    0.000000] / __|/ __| _ \___ / _(_)_ _ _ ____ __ ____ _ _ _ ___
[    0.000000] \__ | (__|  _|___|  _| | '_| '  \ V  V / _` | '_/ -_)
[    0.000000] |___/\___|_|     |_| |_|_| |_|_|_\_/\_/\__,_|_| \___|
[    0.000000] 
[    0.000000] d163a08
[    0.000000] 
[    0.000000] [CMN_SKEENA] Multichip mode: no
[    0.000000] [CMN_SKEENA] Chip ID: 0
[    0.000000] [PVT] Morello Sensor Library version 1.0

[    0.000000] [PVT] Started driver version 1.0
[    0.000000] [MORELLO SYSTEM] Requesting SYSTOP initialization...
[    0.000000] [FWK] Module initialization complete!
[    0.000000] [CMN_SKEENA] Starting discovery...
[    0.000000] [CMN_SKEENA] 
[    0.000000] [CMN_SKEENA] XP (4, 1) ID:264, LID:9
[    0.000000] [CMN_SKEENA] 
[    0.000000] [CMN_SKEENA] XP (4, 0) ID:256, LID:4
[    0.000000] [CMN_SKEENA] 
[    0.000000] [CMN_SKEENA] XP (3, 1) ID:200, LID:8
[    0.000000] [CMN_SKEENA]   HN-F ID:200, LID:3 @0x71900000
[    0.000000] [CMN_SKEENA] 
[    0.000000] [CMN_SKEENA] XP (3, 0) ID:192, LID:3
[    0.000000] [CMN_SKEENA]   HN-F ID:196, LID:1 @0x71804000
[    0.000000] [CMN_SKEENA]   Found external node ID: 192
[    0.000000] [CMN_SKEENA] 
[    0.000000] [CMN_SKEENA] XP (2, 1) ID:136, LID:7
[    0.000000] [CMN_SKEENA]   Found external node ID: 140
[    0.000000] [CMN_SKEENA]   HN-F ID:136, LID:2 @0x71100000
[    0.000000] [CMN_SKEENA] 
[    0.000000] [CMN_SKEENA] XP (2, 0) ID:128, LID:2
[    0.000000] [CMN_SKEENA]   HN-F ID:132, LID:0 @0x71004000
[    0.000000] [CMN_SKEENA]   SBSX ID:128, LID:0 @0x71000000
[    0.000000] [CMN_SKEENA] 
[    0.000000] [CMN_SKEENA] XP (1, 1) ID:72, LID:6
[    0.000000] [CMN_SKEENA]   Found CXLA at node ID: 78
[    0.000000] [CMN_SKEENA]   RN-SAM ID:76, LID:0 @0x70954000
[    0.000000] [CMN_SKEENA]   CXHA ID:76, LID:0 @0x70914000
[    0.000000] [CMN_SKEENA]   CXRA ID:76, LID:0 @0x70904000
[    0.000000] [CMN_SKEENA]   HN-I ID:72, LID:1 @0x70910000
[    0.000000] [CMN_SKEENA] 
[    0.000000] [CMN_SKEENA] XP (1, 0) ID:64, LID:1
[    0.000000] [CMN_SKEENA]   HN-I ID:68, LID:0 @0x70854000
[    0.000000] [CMN_SKEENA]   DTC ID:68, LID:0 @0x70834000
[    0.000000] [CMN_SKEENA]   DVM ID:68, LID:0 @0x70824000
[    0.000000] [CMN_SKEENA]   RN-SAM ID:64, LID:0 @0x70820000
[    0.000000] [CMN_SKEENA]   RN-D ID:64, LID:2 @0x70810000
[    0.000000] [CMN_SKEENA] 
[    0.000000] [CMN_SKEENA] XP (0, 1) ID:8, LID:5
[    0.000000] [CMN_SKEENA]   RN-SAM ID:12, LID:0 @0x70124000
[    0.000000] [CMN_SKEENA]   RN-D ID:12, LID:4 @0x70114000
[    0.000000] [CMN_SKEENA]   RN-SAM ID:8, LID:0 @0x70120000
[    0.000000] [CMN_SKEENA]   RN-D ID:8, LID:3 @0x70110000
[    0.000000] [CMN_SKEENA] 
[    0.000000] [CMN_SKEENA] XP (0, 0) ID:0, LID:0
[    0.000000] [CMN_SKEENA]   RN-SAM ID:4, LID:0 @0x70024000
[    0.000000] [CMN_SKEENA]   RN-D ID:4, LID:1 @0x70014000
[    0.000000] [CMN_SKEENA]   RN-SAM ID:0, LID:0 @0x70020000
[    0.000000] [CMN_SKEENA]   RN-D ID:0, LID:0 @0x70010000
[    0.000000] [CMN_SKEENA] Total internal RN-SAM nodes: 6
[    0.000000] [CMN_SKEENA] Total external RN-SAM nodes: 2
[    0.000000] [CMN_SKEENA] Total HN-F nodes: 4
[    0.000000] [CMN_SKEENA] Total RN-F nodes: 2
[    0.000000] [CMN_SKEENA] Total RN-D nodes: 5
[    0.000000] [CMN_SKEENA] Total RN-I nodes: 0
[    0.000000] [CMN_SKEENA] CCIX CXLA node at: 0x70924000
[    0.000000] [CMN_SKEENA] CCIX CXRA node at: 0x70904000
[    0.000000] [CMN_SKEENA] CCIX CXHA node at: 0x70914000
[    0.000000] [CMN_SKEENA] Configuring RN-SAM for node id 76 at 0x70954000
[    0.000000] [CMN_SKEENA]   [0x0000000000000000 - 0x000007FFFFFFFFFF] System 
[    0.000000] [CMN_SKEENA]   [0x0000000000000000 - 0x0000000007FFFFFF] Sub-Sys
[    0.000000] [CMN_SKEENA]   [0x0000000008000000 - 0x000000000FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000010000000 - 0x000000001FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000020000000 - 0x000000003FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000040000000 - 0x000000005FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000060000000 - 0x000000006FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000070000000 - 0x000000007FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000400000000 - 0x00000007FFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000800000000 - 0x0000000FFFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000001000000000 - 0x0000001FFFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000002000000000 - 0x00000027FFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000002800000000 - 0x0000002FFFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000003000000000 - 0x0000003FFFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000004000000000 - 0x0000004FFFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000005000000000 - 0x0000005FFFFFFFFF] System 
[    0.000000] [CMN_SKEENA]   [0x0000006000000000 - 0x0000007FFFFFFFFF] System 
[    0.000000] [CMN_SKEENA]   [0x0000008000000000 - 0x000000807FFFFFFF] System 
[    0.000000] [CMN_SKEENA]   [0x0000040000000000 - 0x000007FFFFFFFFFF] CCIX
[    0.000000] [CMN_SKEENA] Configuring RN-SAM for node id 64 at 0x70820000
[    0.000000] [CMN_SKEENA]   [0x0000000000000000 - 0x000007FFFFFFFFFF] System 
[    0.000000] [CMN_SKEENA]   [0x0000000000000000 - 0x0000000007FFFFFF] Sub-Sys
[    0.000000] [CMN_SKEENA]   [0x0000000008000000 - 0x000000000FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000010000000 - 0x000000001FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000020000000 - 0x000000003FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000040000000 - 0x000000005FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000060000000 - 0x000000006FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000070000000 - 0x000000007FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000400000000 - 0x00000007FFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000800000000 - 0x0000000FFFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000001000000000 - 0x0000001FFFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000002000000000 - 0x00000027FFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000002800000000 - 0x0000002FFFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000003000000000 - 0x0000003FFFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000004000000000 - 0x0000004FFFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000005000000000 - 0x0000005FFFFFFFFF] System 
[    0.000000] [CMN_SKEENA]   [0x0000006000000000 - 0x0000007FFFFFFFFF] System 
[    0.000000] [CMN_SKEENA]   [0x0000008000000000 - 0x000000807FFFFFFF] System 
[    0.000000] [CMN_SKEENA]   [0x0000040000000000 - 0x000007FFFFFFFFFF] CCIX
[    0.000000] [CMN_SKEENA] Configuring RN-SAM for node id 12 at 0x70124000
[    0.000000] [CMN_SKEENA]   [0x0000000000000000 - 0x000007FFFFFFFFFF] System 
[    0.000000] [CMN_SKEENA]   [0x0000000000000000 - 0x0000000007FFFFFF] Sub-Sys
[    0.000000] [CMN_SKEENA]   [0x0000000008000000 - 0x000000000FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000010000000 - 0x000000001FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000020000000 - 0x000000003FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000040000000 - 0x000000005FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000060000000 - 0x000000006FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000070000000 - 0x000000007FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000400000000 - 0x00000007FFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000800000000 - 0x0000000FFFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000001000000000 - 0x0000001FFFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000002000000000 - 0x00000027FFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000002800000000 - 0x0000002FFFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000003000000000 - 0x0000003FFFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000004000000000 - 0x0000004FFFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000005000000000 - 0x0000005FFFFFFFFF] System 
[    0.000000] [CMN_SKEENA]   [0x0000006000000000 - 0x0000007FFFFFFFFF] System 
[    0.000000] [CMN_SKEENA]   [0x0000008000000000 - 0x000000807FFFFFFF] System 
[    0.000000] [CMN_SKEENA]   [0x0000040000000000 - 0x000007FFFFFFFFFF] CCIX
[    0.000000] [CMN_SKEENA] Configuring RN-SAM for node id 8 at 0x70120000
[    0.000000] [CMN_SKEENA]   [0x0000000000000000 - 0x000007FFFFFFFFFF] System 
[    0.000000] [CMN_SKEENA]   [0x0000000000000000 - 0x0000000007FFFFFF] Sub-Sys
[    0.000000] [CMN_SKEENA]   [0x0000000008000000 - 0x000000000FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000010000000 - 0x000000001FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000020000000 - 0x000000003FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000040000000 - 0x000000005FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000060000000 - 0x000000006FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000070000000 - 0x000000007FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000400000000 - 0x00000007FFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000800000000 - 0x0000000FFFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000001000000000 - 0x0000001FFFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000002000000000 - 0x00000027FFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000002800000000 - 0x0000002FFFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000003000000000 - 0x0000003FFFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000004000000000 - 0x0000004FFFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000005000000000 - 0x0000005FFFFFFFFF] System 
[    0.000000] [CMN_SKEENA]   [0x0000006000000000 - 0x0000007FFFFFFFFF] System 
[    0.000000] [CMN_SKEENA]   [0x0000008000000000 - 0x000000807FFFFFFF] System 
[    0.000000] [CMN_SKEENA]   [0x0000040000000000 - 0x000007FFFFFFFFFF] CCIX
[    0.000000] [CMN_SKEENA] Configuring RN-SAM for node id 4 at 0x70024000
[    0.000000] [CMN_SKEENA]   [0x0000000000000000 - 0x000007FFFFFFFFFF] System 
[    0.000000] [CMN_SKEENA]   [0x0000000000000000 - 0x0000000007FFFFFF] Sub-Sys
[    0.000000] [CMN_SKEENA]   [0x0000000008000000 - 0x000000000FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000010000000 - 0x000000001FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000020000000 - 0x000000003FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000040000000 - 0x000000005FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000060000000 - 0x000000006FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000070000000 - 0x000000007FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000400000000 - 0x00000007FFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000800000000 - 0x0000000FFFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000001000000000 - 0x0000001FFFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000002000000000 - 0x00000027FFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000002800000000 - 0x0000002FFFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000003000000000 - 0x0000003FFFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000004000000000 - 0x0000004FFFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000005000000000 - 0x0000005FFFFFFFFF] System 
[    0.000000] [CMN_SKEENA]   [0x0000006000000000 - 0x0000007FFFFFFFFF] System 
[    0.000000] [CMN_SKEENA]   [0x0000008000000000 - 0x000000807FFFFFFF] System 
[    0.000000] [CMN_SKEENA]   [0x0000040000000000 - 0x000007FFFFFFFFFF] CCIX
[    0.000000] [CMN_SKEENA] Configuring RN-SAM for node id 0 at 0x70020000
[    0.000000] [CMN_SKEENA]   [0x0000000000000000 - 0x000007FFFFFFFFFF] System 
[    0.000000] [CMN_SKEENA]   [0x0000000000000000 - 0x0000000007FFFFFF] Sub-Sys
[    0.000000] [CMN_SKEENA]   [0x0000000008000000 - 0x000000000FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000010000000 - 0x000000001FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000020000000 - 0x000000003FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000040000000 - 0x000000005FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000060000000 - 0x000000006FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000070000000 - 0x000000007FFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000400000000 - 0x00000007FFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000000800000000 - 0x0000000FFFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000001000000000 - 0x0000001FFFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000002000000000 - 0x00000027FFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000002800000000 - 0x0000002FFFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000003000000000 - 0x0000003FFFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000004000000000 - 0x0000004FFFFFFFFF] I/O
[    0.000000] [CMN_SKEENA]   [0x0000005000000000 - 0x0000005FFFFFFFFF] System 
[    0.000000] [CMN_SKEENA]   [0x0000006000000000 - 0x0000007FFFFFFFFF] System 
[    0.000000] [CMN_SKEENA]   [0x0000008000000000 - 0x000000807FFFFFFF] System 
[    0.000000] [CMN_SKEENA]   [0x0000040000000000 - 0x000007FFFFFFFFFF] CCIX
[    0.000000] [CMN_SKEENA] Done
[    0.000000] [APContext] Zeroing AP context area [0xa4000fc0 - 0xa4001000]
[    0.000000] [DDR] Starting DDR subsystem initialization at 1466 MHz
[    0.000000] [DDR] Identifying connected DIMM cards...
[    0.000000]     DIMM 0 information:
[    0.000000]     Manufacturer ID = 0x80 0x2c
[    0.000000]     Module part number = 9ASF1G72PZ-2G9E1    Ø#
[    0.000000]     Module serial number = 0x30 0x7a 0xa1 0x7
[    0.000000]     Module manufacturing week 30 year 21
[    0.000000]     DIMM 1 information:
[    0.000000]     Manufacturer ID = 0x80 0x2c
[    0.000000]     Module part number = 9ASF1G72PZ-2G9E1    Ø#
[    0.000000]     Module serial number = 0x30 0x7a 0x87 0x2f
[    0.000000]     Module manufacturing week 30 year 21
[    0.000000] [DDR] Initialising DMC-Bing at 0x4e000000
[    0.000000] [DDR] Configuring interrupts for DMC0
[    0.000000] [DDR] Writing functional settings
[    0.000000] [DDR-PHY] Initializing PHY at 0x0x50604000 for 1466 MHz speed
[    0.000000] [DDR] Sending direct DDR commands
[    0.000000] [DDR] Training DDR memories...
[    0.000000] [DDR] Write leveling rank 1... 
[    0.000000] [DDR] PASS
[    0.000000] [DDR] Read gate training
[    0.000000] [DDR] A side...
[    0.000000] [DDR] PASS
[    0.000000] [DDR] Read eye training
[    0.000000] [DDR] A side...
[    0.000000] [DDR] PASS
[    0.000000] [DDR] B side...
[    0.000000] [DDR] PASS
[    0.000000] [DDR] MC initiated update...
[    0.000000] [DDR] PASS
[    0.000000] [DDR-PHY] Post training PHY setting at 0x50604000
[    0.000000] [DDR-PHY] Performing write eye training...
[    0.000000] [DDR-PHY] PASS!
[    0.000000] [DDR] Enable DIMM refresh...
[    0.000000] [DDR] PASS
[    0.000000] [DDR] Setting DMC to READY mode
[    0.000000] [DDR] DMC init done.
[    0.000000] [DDR] Initialising DMC-Bing at 0x4e100000
[    0.000000] [DDR] Configuring interrupts for DMC1
[    0.000000] [DDR] Writing functional settings
[    0.000000] [DDR-PHY] Initializing PHY at 0x0x50614000 for 1466 MHz speed
[    0.000000] [DDR] Sending direct DDR commands
[    0.000000] [DDR] Training DDR memories...
[    0.000000] [DDR] Write leveling rank 1...

MCP

[    0.000000]  ___  ___ ___      __ _
[    0.000000] / __|/ __| _ \___ / _(_)_ _ _ ____ __ ____ _ _ _ ___
[    0.000000] \__ | (__|  _|___|  _| | '_| '  \ V  V / _` | '_/ -_)
[    0.000000] |___/\___|_|     |_| |_|_| |_|_|_\_/\_/\__,_|_| \___|
[    0.000000] 
[    0.000000] v2.7.0_2020-11-19_07-20-34-d49e1335
[    0.000000] 
[    0.000000] [FWK] Module initialization complete!
[    0.000000] [ROM] Trying to identify FIP at 0x30000000
[    0.000000] [ROM] Located MCP_BL2:
[    0.000000] [ROM]   address: 0x30000060
[    0.000000] [ROM]   size   : 30892
[    0.000000] [ROM]   flags  : 0x0000000000000000
[    0.000000] [ROM] Copying MCP_BL2 to ITCRAM...!
[    0.000000] [ROM] Done!
[    0.000000] [ROM] Jumping to MCP_BL2
[    0.000000]  ___  ___ ___      __ _
[    0.000000] / __|/ __| _ \___ / _(_)_ _ _ ____ __ ____ _ _ _ ___
[    0.000000] \__ | (__|  _|___|  _| | '_| '  \ V  V / _` | '_/ -_)
[    0.000000] |___/\___|_|     |_| |_|_| |_|_|_\_/\_/\__,_|_| \___|
[    0.000000] 
[    0.000000] d163a08
[    0.000000] 
[    0.000000] [FWK] Module initialization complete!
[    0.000000] [MCP SYSTEM] Waiting for handshake pattern from SCP...

Top replies

Parents

0 Anurag Koul over 1 year ago

Hi, Brett.

From the SCP logs, it seems like the DDR write levelling training for one of the two connected DDR DIMMs didn't go through. As a result, SCP firmware's initialisation terminated prematurely which explains why AP (and hence its console) was never brought up. The suspicion is that it could be down to the DIMM seating in the slot, so reseating the DIMMs (and/or swapping them) might do the trick.

Please let us know if the error persists even after the reseating.

Kind regards,

Anurag
Cancel
Up +1 Down

Cancel

Reply

0 Anurag Koul over 1 year ago

Hi, Brett.

From the SCP logs, it seems like the DDR write levelling training for one of the two connected DDR DIMMs didn't go through. As a result, SCP firmware's initialisation terminated prematurely which explains why AP (and hence its console) was never brought up. The suspicion is that it could be down to the DIMM seating in the slot, so reseating the DIMMs (and/or swapping them) might do the trick.

Please let us know if the error persists even after the reseating.

Kind regards,

Anurag
Cancel
Up +1 Down

Cancel

Children

0 Brett Wilson over 1 year ago in reply to Anurag Koul

HI Anurag,

Thanks for the insight and debug ideas. I tried reseating them as well as swapping but I get the same output on the SCP log (except for the swapping of DIMM serial number locations). It always seems to hang on the second DIMM regardless of swapping so I'm assuming that the DIMMs are okay.

Brett
Cancel
Up 0 Down

Cancel
+1 Kevin Brodsky over 1 year ago in reply to Brett Wilson

HI Brett,

From the evidence so far, our hardware folks suspect that the board has developed a fault. The best would be to log a support request here:

https://services.arm.com/support/s/contactsupport

Cheers,
Kevn
Cancel
Up +1 Down

Cancel