problem in getting data

Thanks for reply and suggesting me.I also make a simple program to get yes word from the controller but it give the same result as in sensor program.my code of this prog. Is

#include<reg51.h> void se(unsigned char) ; void ms(unsigned int value) ; void main(void) { unsigned char z; TMOD=0x20; TH1=0xFA; SCON=0x50; TR1=1; for(z=0;;z++) { se('Y'); ms(255); se('E'); ms(255); se('S'); ms(255); se(' '); } } void se(unsigned char x) { SBUF=x; while(TI==0); TI=0; } void ms(unsigned int value)
{ unsigned char x,y; for(x=0;x<value;x++); for(y=0;y<255;y++);
}

And my code for sensor data is as follows

#include<reg51.h>
void con(unsigned char value);
void ms(unsigned int value);
void se(unsigned char) ;
sbit ALE=P3^6;
sbit OE=P3^5;
sbit SC=P3^3;
sbit EOC=P3^4;
sbit ADDR_A=P1^0;
sbit ADDR_B=P1^1;
sbit ADDR_C=P1^2; main() { unsigned char v;
TMOD=0x20; TH1=0xFA; SCON=0x50; TR1=1;
//MYDATA=0xFF; P2=0xFF; EOC=1; ALE=0; OE=0; SC=0; while(1) { ADDR_C=0; ADDR_B=0; ADDR_A=1; ms(1); SC=1; ms(1); ALE=0; SC=0; while(EOC==1); while(EOC==0); OE=1; ms(1); v=P2; OE=0; con(v); }
} void ms(unsigned int value)
{ unsigned char x,y; for(x=0;x<value;x++); for(y=0;y<255;y++);
} void con(unsigned char value)
{ unsigned char x,d1,d2,d3; x=value/10; d1=value%10; d2=x%10; d3=x/10; se(d1); ms(255); se(d2); ms(255); se(d3); ms(255);
} void se(unsigned char x) { SBUF=x; while(TI==0); TI=0; }

can u tell me the problem in my code.again thank u.

Thanks for reply and suggesting me.I also make a simple program to get yes word from the controller but it give the same result as in sensor program.my code of this prog. Is

#include<reg51.h> void se(unsigned char) ; void ms(unsigned int value) ; void main(void) { unsigned char z; TMOD=0x20; TH1=0xFA; SCON=0x50; TR1=1; for(z=0;;z++) { se('Y'); ms(255); se('E'); ms(255); se('S'); ms(255); se(' '); } } void se(unsigned char x) { SBUF=x; while(TI==0); TI=0; } void ms(unsigned int value)
{ unsigned char x,y; for(x=0;x<value;x++); for(y=0;y<255;y++);
}

And my code for sensor data is as follows

#include<reg51.h>
void con(unsigned char value);
void ms(unsigned int value);
void se(unsigned char) ;
sbit ALE=P3^6;
sbit OE=P3^5;
sbit SC=P3^3;
sbit EOC=P3^4;
sbit ADDR_A=P1^0;
sbit ADDR_B=P1^1;
sbit ADDR_C=P1^2; main() { unsigned char v;
TMOD=0x20; TH1=0xFA; SCON=0x50; TR1=1;
//MYDATA=0xFF; P2=0xFF; EOC=1; ALE=0; OE=0; SC=0; while(1) { ADDR_C=0; ADDR_B=0; ADDR_A=1; ms(1); SC=1; ms(1); ALE=0; SC=0; while(EOC==1); while(EOC==0); OE=1; ms(1); v=P2; OE=0; con(v); }
} void ms(unsigned int value)
{ unsigned char x,y; for(x=0;x<value;x++); for(y=0;y<255;y++);
} void con(unsigned char value)
{ unsigned char x,d1,d2,d3; x=value/10; d1=value%10; d2=x%10; d3=x/10; se(d1); ms(255); se(d2); ms(255); se(d3); ms(255);
} void se(unsigned char x) { SBUF=x; while(TI==0); TI=0; }

can u tell me the problem in my code.again thank u.

"can u tell me the problem in my code.again thank u."

No. I can just barely tell that this looks similar to C - most possibly from the obfuscated-C contest. Didn't you read the posting instructions for source code? Look two lines above the input box where you write your posts.

And for best result, you should indent your source with spaces instead of tab characters.

no i did not read the posting instruction.no problem in my software but the incompatibility of the baurd rate.now it's working well.thanks to give attention to my problem and sorry for late reply.