We are running a survey to help us improve the experience for all of our members. If you see the survey appear, please take the time to tell us about your experience if you can.
Hi all.. Im quite new to 8051. Im doing a project that requires me to display value of a peak voltage on a LCD.
Anyway, Im stuck in testing the LCD. I have connected the LCD(Powertip PC 0802-A), otherwise known as 214-3288, to my 8051 development kit. The kit that im using is C8051F206-TB. I connected databus 0-7 to port 3 and RS to P2.4, R/W to P2.5, and EN to P2.6
I also have gone online to source for programs to display "Hello World" on the LCD. I have found a few in C or asm, but i have learnt the basic of assembly language, so i don't really understand C language.
Below is a program i found in 8052.com
$include (c8051f200.inc) CSEG AT 0000H LJMP MAIN CSEG AT 0100H MAIN:LCALL CONFIG LCALL INIT_LCD LCALL CLEAR_LCD LCALL HELLO CONFIG:MOV PRT0MX, #000H ; PRT0MX: Initial Reset Value MOV PRT1MX, #000H ; PRT1MX: Initial Reset Value MOV PRT2MX, #000H ; PRT2MX: Initial Reset Value MOV P2MODE, #0FFH ; Input Configuration for P2 MOV PRT3CF, #0FFH ; Output configuration for P3 INIT_LCD: CLR P2.4 MOV P3,#38H SETB P2.6 CLR P2.6 LCALL WAIT_LCD CLR P2.4 MOV P3,#0EH SETB P2.6 CLR P2.6 LCALL WAIT_LCD CLR P2.4 MOV P3,#06H SETB P2.6 CLR P2.6 LCALL WAIT_LCD RET HELLO: LCALL INIT_LCD LCALL CLEAR_LCD MOV A,#48H LCALL WRITE_TEXT MOV A,#45H LCALL WRITE_TEXT MOV A,#4CH LCALL WRITE_TEXT MOV A,#4CH LCALL WRITE_TEXT MOV A,#4FH LCALL WRITE_TEXT CLR P2.4 MOV P3,#0CAH SETB P2.6 CLR P2.6 LCALL WRITE_TEXT MOV A,#57H LCALL WRITE_TEXT MOV A,#4FH LCALL WRITE_TEXT MOV A,#52H LCALL WRITE_TEXT MOV A,#4CH LCALL WRITE_TEXT MOV A,#44H LCALL WRITE_TEXT WAIT_LCD: CLR P2.6 ;Start LCD command CLR P2.4 ;It's a command SETB P2.5 ;It's a read command MOV P3,#0FFH ;Set all pins to FF initially SETB P2.6 ;Clock out command to LCD MOV A,P3 ;Read the return value JB ACC.7,WAIT_LCD CLR P2.6 ;Finish the command CLR P2.5 ;Turn off RW for future commands RET CLEAR_LCD:CLR P2.4 MOV P3,#01H SETB P2.6 CLR P2.6 LCALL WAIT_LCD RET WRITE_TEXT:SETB P2.4 MOV P3,A SETB P2.6 CLR P2.6 LCALL WAIT_LCD RET END
You meant i have to calculate the clock cycles for each routine and make sure that they have enuff delay?
Not quite. You will have to determine the timing of those signals. Calculating is only one of many ways of determining it, and hardly ever the best one to choose.
The best method would be to use an oscilloscope or logic analyzer on the actual hardware. If you really can't get your hands on a 'scope, the next best thing is the logic analyzer built into the uVision simulator debugger. Using that, you can generate almost exactly the same kind of diagram as you'll find in the datasheet(s) of devices you're trying to control. That can make things a whole lot easier to check.