We are running a survey to help us improve the experience for all of our members. If you see the survey appear, please take the time to tell us about your experience if you can.
Hi Everybody, I'm still experimenting with Infineon's XC161 Starter Kit using the Keil C166 compiler, v4.27 (linker version 4.28). Almost everything I need works OK now, except the external bus controller. Below I'll describe my situation: Hardware ======== I've connected the RAM to the processor by setting switch S101.8. This is the configuration for the multiplexed mode, so I also switched S103.1 and S103.2 off for 16 bits multiplexed mode. The CS-lines are enabled by off-switching S102.6 and S102.7. I use 4-bit address lines by setting S102.4 and S102.5. S102.8 is switched on to use /WR and /BHE as /WRL and /WRH. Software ======== In the startup file (START_V2.A66) I configured the EBC as follows:
$SET (CONFIG_EBC = 1) _SAPEN EQU 4 _CSPEN EQU 5 _ARBEN EQU 0 _SLAVE EQU 0 _EBCDIS EQU 0 _WRCFG EQU 1 _BYTDIS EQU 0 _ALEDIS EQU 0 _RDYDIS EQU 0 _RDYPOL EQU 0 _APDIS EQU 0 _DHPDIS EQU 0
$SET (CONFIG_CS1 = 1) _ADDR1 EQU 0x400000 _SIZE1 EQU 256*KB _ENCS1 EQU 1 _RDYEN1 EQU 0 _RDYMOD1 EQU 0 _BTYP1 EQU 3 _PHA1 EQU 3 _PHB1 EQU 1 _PHC1 EQU 3 _PHD1 EQU 1 _PHE1 EQU 25 _RDPHF1 EQU 3 _WRPHF1 EQU 3
VALUE PUBLIC SYMBOL NAME REP TGR CLASS SECTION ======================================================================= -- cut -- 3F8000H ?C_NDATABASE CONST --- --- --- -- cut --
Hi Steffen, no idea about what goes wrong with the timings, if Dennis not could help you with his experiences I would e-mail my project files for muxed mode ( and so my timings ). Please leave your mail-account here. I send my SPI-Routines to you, which works with a terminal program via ASC0 Second ASC interface You can freely use the second ASC interface. The ASC1 is implemented now with all newer derivatives, since Infineon recognized that a second micro line is more daerer than test the second interface on each chip. The best way is to develop the ASC routines with DAvE for XC161 and than copy the related routines to your project, since the DAvE DIP does not included the second ASC at this time. Otherwise you can copy the ASC0 files to ASC1 files, but you have to dadapted the MAIN.H with the addresses of ASC1 interface. Take care to enable the ASC1 device in startup-file. This is one thing that DAvE does wrong !! Stefan
Hi Stefan, I've got the ASC1 not running on my XC164 SK. I've tried your proposals and the software works fine in simulator with settings for XC161. I've also measured some signals on MAX232 with oszi. I've seen the transmit datas (T1 IN and T1 OUT in schematics) for configuration ASC0 , but nothing, if I'll use ASC1 (T2 IN, T2 OUT). So I have to assume, that ASC1 is not available on my XC164 or on my derivative, may be it's production step dependend. My eMail account is Steffen.Niekler@gmx.de Bye Steffen
Hi Steffen, please check your account. I e-mailed the files. Stefan
Hi Stefan, thank you for the code, at the moment I could'nt read it, because our mail server is down. But I got the second serial interface running. The problem were the right port and alternate settings of ASC1. I used the code for XC161, and there are some differences to XC164, because of lower pin count. The solution is:
P3 |= 0x0020; /* SET PORT 3.5 OUTPUT LATCH (TXD1) */ DP3 |= 0x0020; /* SET PORT 3.5 DIRECTION CONTROL (TXD1 OUTPUT) */ DP3 &= 0xFFFD; /* RESET PORT 3.1 DIRECTION CONTROL (RXD1 INPUT) */ ASC1_TIC = 0x80; /* SET TRANSMIT INTERRUPT FLAG */ ASC1_RIC = 0x00; /* DELETE RECEIVE INTERRUPT FLAG */ ASC1_BG = 0x20; /* SET BAUDRATE TO 38400 BAUD @ 40MHz */ ASC1_CON = 0x8011; /* SET SERIAL MODE */ ALTSEL0P3 |= 0x0022; /* Configure port pins for serial interface 1 */
Hi Steffen, well done job! ;-} As I mentioned I got it too some times before. But now you can sure to use your code allways with the new devices. If some questions about my code samples, feel free to contact me. Stefan