sir i am facing a problem to map my inputs and outputs in the if condition that is in read input data bit for multiple pins kindly help me the same.
#include "stm32f0xx.h" #include "stm32f0308_Discovery.h"
#define out0 GPIO_Pin_0 #define out1 GPIO_Pin_1 #define out2 GPIO_Pin_2 #define out3 GPIO_Pin_3 #define out4 GPIO_Pin_4 #define out_GPIO GPIOC
void TM_Delay_Init(void); void TM_DelayMillis(uint32_t millis); void TM_DelayMillis1(uint32_t millis); void TM_DelayMillis2(uint32_t millis);
GPIO_InitTypeDef GPIO_InitStructure ;
uint32_t multiplier;
int main(void) { SystemInit(); SystemCoreClockUpdate(); RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA | RCC_AHBPeriph_GPIOC, ENABLE); /* Configure PA in input mode */ GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0 ; GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN; GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL; GPIO_Init(GPIOA, &GPIO_InitStructure); /*configure PC in output mode */ GPIOC->MODER |= ((GPIO_MODER_MODER0_0)|(GPIO_MODER_MODER1_0)|(GPIO_MODER_MODER2_0)|(GPIO_MODER_MODER3_0)|(GPIO_MODER_MODER4_0)|(GPIO_MODER_MODER5_0)) ; //GPIOC-> GPIO_MODER_MODER8_0 = 0x01; GPIOC->OTYPER &= ~((GPIO_OTYPER_OT_0)|(GPIO_OTYPER_OT_1)|(GPIO_OTYPER_OT_2)|(GPIO_OTYPER_OT_3)|(GPIO_OTYPER_OT_4)|(GPIO_OTYPER_OT_5)) ; //GPIOC->OTYPER = 0x00; GPIOC->OSPEEDR |= ((GPIO_OSPEEDER_OSPEEDR0)|(GPIO_OSPEEDER_OSPEEDR1)|(GPIO_OSPEEDER_OSPEEDR2)|(GPIO_OSPEEDER_OSPEEDR3)|(GPIO_OSPEEDER_OSPEEDR4)|(GPIO_OSPEEDER_OSPEEDR5)); //GPIOC->OSPEEDR = 0x00; GPIOC->PUPDR &= ~((GPIO_PUPDR_PUPDR0)|(GPIO_PUPDR_PUPDR1)|(GPIO_PUPDR_PUPDR2)|(GPIO_PUPDR_PUPDR3)|(GPIO_PUPDR_PUPDR4)|(GPIO_PUPDR_PUPDR5)); while(1) { if(GPIO_ReadInputDataBit(GPIOA, GPIO_Pin_0)==1) { GPIO_SetBits(GPIOC,(out0)|(out1)|(out2)|(out3)|(out4)); TM_DelayMillis(7); GPIO_ResetBits(GPIOC,(out0)|(out1)|(out2)|(out3)|(out4)); while (GPIO_ReadInputDataBit(GPIOA, GPIO_Pin_0)==1) { GPIO_SetBits(GPIOC,(out0)|(out1)|(out2)|(out3)|(out4)); TM_DelayMillis1(3); GPIO_ResetBits(GPIOC,(out0)|(out1)|(out2)|(out3)|(out4)); TM_DelayMillis2(22); } } } }
void TM_DelayMillis(uint32_t millis) { /* Multiply millis with multipler */ /* Substract 10 */ millis = 100 * millis * multiplier - 10; /* 4 cycles for one loop */ while (millis--); }
void TM_DelayMillis1(uint32_t millis) { /* Multiply millis with multipler */ /* Substract 10 */ millis = 1 * millis * multiplier - 10; /* 4 cycles for one loop */ while (millis--); }
void TM_DelayMillis2(uint32_t millis) { /* Multiply millis with multipler */ /* Substract 10 */ millis = 1 * millis * multiplier - 10; /* 4 cycles for one loop */ while (millis--); }
void TM_Delay_Init(void) { RCC_ClocksTypeDef RCC_Clocks;
/* Get system clocks */ RCC_GetClocksFreq(&RCC_Clocks);
/* While loop takes 4 cycles */ /* For 1 us delay, we need to divide with 4M */ multiplier = RCC_Clocks.HCLK_Frequency / 4000000; }
let me tell you the application i have 5 input pins let take as switches and my 5 led's as my output when my first switch is "on" my first led should "on(set)" for 700msec and should be low(reset) after that it should be "high" for 3msec and should be "low" for 22msec this loop have to be repeated continuously until my switch is on.vice versa for all the pins.when i make high of any input pin my relevant output should be high not all the pins.
this is my application sir kindly help me in this.
If it was my project I would try the following. First I would need a oscilloscope to view the created signals.
Second, I would obtain a solderless breadboard and wires to wire up the header pins to the bread board.
I would wire up the following pins as input
Inputs P1.15 PA0 P1.16 PA1 P1.17 PA2 P1.18 PA3 P1.21 PA4 P1.22 PA5
Outputs P1.27 PB0 P1.28 PB1 P1.29 PB2 P2.11 PA3 P2.10 PA4 P2.9 PA5
and GROUND AND THREE VOLTS
P1.1 3 Volts P1.2 GND
All this information can be checked by looking at the schematic.
Then inputs can be set hi or low on the Breadboard as required.
then in a loop you can read the input pins as a 32 bit word.
I think you can take that word and write it to the outputs to set/reset the outputs as the inputs are configured (timed as needed).