sir i am facing a problem to map my inputs and outputs in the if condition that is in read input data bit for multiple pins kindly help me the same.
#include "stm32f0xx.h" #include "stm32f0308_Discovery.h"
#define out0 GPIO_Pin_0 #define out1 GPIO_Pin_1 #define out2 GPIO_Pin_2 #define out3 GPIO_Pin_3 #define out4 GPIO_Pin_4 #define out_GPIO GPIOC
void TM_Delay_Init(void); void TM_DelayMillis(uint32_t millis); void TM_DelayMillis1(uint32_t millis); void TM_DelayMillis2(uint32_t millis);
GPIO_InitTypeDef GPIO_InitStructure ;
uint32_t multiplier;
int main(void) { SystemInit(); SystemCoreClockUpdate(); RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA | RCC_AHBPeriph_GPIOC, ENABLE); /* Configure PA in input mode */ GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0 ; GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN; GPIO_InitStructure.GPIO_PuPd = GPIO_PuPd_NOPULL; GPIO_Init(GPIOA, &GPIO_InitStructure); /*configure PC in output mode */ GPIOC->MODER |= ((GPIO_MODER_MODER0_0)|(GPIO_MODER_MODER1_0)|(GPIO_MODER_MODER2_0)|(GPIO_MODER_MODER3_0)|(GPIO_MODER_MODER4_0)|(GPIO_MODER_MODER5_0)) ; //GPIOC-> GPIO_MODER_MODER8_0 = 0x01; GPIOC->OTYPER &= ~((GPIO_OTYPER_OT_0)|(GPIO_OTYPER_OT_1)|(GPIO_OTYPER_OT_2)|(GPIO_OTYPER_OT_3)|(GPIO_OTYPER_OT_4)|(GPIO_OTYPER_OT_5)) ; //GPIOC->OTYPER = 0x00; GPIOC->OSPEEDR |= ((GPIO_OSPEEDER_OSPEEDR0)|(GPIO_OSPEEDER_OSPEEDR1)|(GPIO_OSPEEDER_OSPEEDR2)|(GPIO_OSPEEDER_OSPEEDR3)|(GPIO_OSPEEDER_OSPEEDR4)|(GPIO_OSPEEDER_OSPEEDR5)); //GPIOC->OSPEEDR = 0x00; GPIOC->PUPDR &= ~((GPIO_PUPDR_PUPDR0)|(GPIO_PUPDR_PUPDR1)|(GPIO_PUPDR_PUPDR2)|(GPIO_PUPDR_PUPDR3)|(GPIO_PUPDR_PUPDR4)|(GPIO_PUPDR_PUPDR5)); while(1) { if(GPIO_ReadInputDataBit(GPIOA, GPIO_Pin_0)==1) { GPIO_SetBits(GPIOC,(out0)|(out1)|(out2)|(out3)|(out4)); TM_DelayMillis(7); GPIO_ResetBits(GPIOC,(out0)|(out1)|(out2)|(out3)|(out4)); while (GPIO_ReadInputDataBit(GPIOA, GPIO_Pin_0)==1) { GPIO_SetBits(GPIOC,(out0)|(out1)|(out2)|(out3)|(out4)); TM_DelayMillis1(3); GPIO_ResetBits(GPIOC,(out0)|(out1)|(out2)|(out3)|(out4)); TM_DelayMillis2(22); } } } }
void TM_DelayMillis(uint32_t millis) { /* Multiply millis with multipler */ /* Substract 10 */ millis = 100 * millis * multiplier - 10; /* 4 cycles for one loop */ while (millis--); }
void TM_DelayMillis1(uint32_t millis) { /* Multiply millis with multipler */ /* Substract 10 */ millis = 1 * millis * multiplier - 10; /* 4 cycles for one loop */ while (millis--); }
void TM_DelayMillis2(uint32_t millis) { /* Multiply millis with multipler */ /* Substract 10 */ millis = 1 * millis * multiplier - 10; /* 4 cycles for one loop */ while (millis--); }
void TM_Delay_Init(void) { RCC_ClocksTypeDef RCC_Clocks;
/* Get system clocks */ RCC_GetClocksFreq(&RCC_Clocks);
/* While loop takes 4 cycles */ /* For 1 us delay, we need to divide with 4M */ multiplier = RCC_Clocks.HCLK_Frequency / 4000000; }
The way the code seems to be written it looks like your input pin is enabling the sequence of ones and zeros.
But when the input is low the sequence is supposed to stop.