LCD 20x4 ( 4 bits ) lib

I know that simply means IO1DIR
IO = Input / Output
1 = Port Identifier
DIR = port the operating direction ( input, output ) .
Sorry if I'm learning to confuse a month and your help was important. I'm sure the question pin R / W lcd . I realized that he is on a pin , but he is in the right GND ? I've done some lcd connections in Proteus and it was so.

I know that simply means IO1DIR
IO = Input / Output
1 = Port Identifier
DIR = port the operating direction ( input, output ) .
Sorry if I'm learning to confuse a month and your help was important. I'm sure the question pin R / W lcd . I realized that he is on a pin , but he is in the right GND ? I've done some lcd connections in Proteus and it was so.

Yes, but isn't it confusing if you have source code that makes use of a constant named "IO1DIR" which seems to imply port 1. But you have a #define that translates IO1DIR into GPIO_GPIO2DIR which seems to be port 2? Wouldn't you be extremely confused if an assign to port 1 actually changes the state of port 2?

Wouldn't you be confused if you indicate blinkers left on your car and the indication inside the car indicates left but the lamps on the outside instead indicates right?

The time/cost of maintainance of source code very much depends on how easy it is to read and understand. So the code should "speak" to the developer. And it most definitely shouldn't lie, because it will come back and haunt you.

I'm sure the question pin R / W LCD . I Realized que he is on a pin , but he is in the right GND ? I've done some lcd connections in Proteus and it was so .
Got it , thanks for the tip .

Jonatan souza.
it seems that your code is changed and is different from what was on my mind.use these codes.

#ifndef __PORTLCD_H
#define __PORTLCD_H

#define USE_FIO         1

#if USE_FIO
#define IODIR_LCD    FIO0DIR
#define IOSET_LCD    FIO0SET
#define IOCLR_LCD    FIO0CLR
#define IOPIN_LCD    FIO0PIN
#else
#define IODIR_LCD    IODIR0
#define IOSET_LCD    IOSET0
#define IOCLR_LCD    IOCLR0
#define IOPIN_LCD    IOPIN0
#endif

/* LCD IO definitions */
#define LCD_E                   ( 1 << 26 )                       /* Enable control pin                */
#define LCD_RW                  ( 1 << 25 )                       /* Read/Write control pin            */
#define LCD_RS                  ( 1 << 24 )                       /* Data/Instruction control          */
#define LCD_CTRL                ( LCD_E | LCD_RW | LCD_RS )       /* Control lines mask                */
#define LCD_DATA                ( 0x0f << 27 )
#define LCD_DATA_START  27                    /* Data lines mask                   */

extern void LCD_init(void);
extern void delay (DWORD cnt) ;
extern void LCD_load(BYTE *fp, DWORD cnt);
extern void LCD_gotoxy(DWORD x, DWORD y);
extern void LCD_cls(void);
extern void LCD_cur_off(void);
extern void LCD_on(void);
extern void LCD_putc(BYTE c);
extern void LCD_puts(BYTE *sp);
extern void LCD_bargraph(DWORD val, DWORD size);
extern void LCD_cur_blink( void );

#endif /* end __PORTLCD_H */

you should just change the Port number and pins according to your project.
and Source code for 20 character length LCDs.

/******************************************************************************
void LCD_init( void )
{
   /* Initialize the ST7066 LCD controller to 4-bit mode. */
#if USE_FIO
        SCS |= 0x00000001;      /* set GPIOx to use Fast I/O */
#endif
   IODIR_LCD |= LCD_CTRL | LCD_DATA;
   IOCLR_LCD  = LCD_RW   | LCD_RS   | LCD_DATA;

   lcd_write_4bit(0x3);                /* Select 4-bit interface            */
   delay (10);
   lcd_write_4bit(0x3);
   delay (10);
   lcd_write_4bit(0x3);
   lcd_write_4bit(0x2);

   lcd_write_cmd(0x28);                /* 2 lines, 5x8 character matrix     */
   lcd_write_cmd(0x0e);                /* Display ctrl:Disp/Curs/Blnk=ON    */
   lcd_write_cmd(0x06);                /* Entry mode: Move right, no shift  */

   LCD_load( (BYTE *)&UserFont, sizeof (UserFont) );
   LCD_cls();
   return;
}

/******************************************************************************
void LCD_gotoxy( DWORD x, DWORD y )
{
   /* Set cursor position on LCD display. Left corner: 1,1, right: 16,2 */
   DWORD c;

   c = x;
   if (y)
   {
      c |= 0x40;
   }
   lcd_write_cmd (c | 0x80);
   lcd_ptr = y*20 + x;
   return;
}

/******************************************************************************
void LCD_putc( BYTE c )
{
   /* Print a character to LCD at current cursor position. */
   if (lcd_ptr == 20)
   {
      lcd_write_cmd (0xc0);
   }
   lcd_write_data(c);
   lcd_ptr++;
   return;
}


/*****************************************************************************
**                            End Of File
******************************************************************************/

I'm using the same code , but I'm getting messages such as: "Controller received command whilst busy" and then another " Attempted to read controller date whilst busy" . What is it?

proteus is not a reliable simulator.test your code on a real hardware. I used this module in some of my projects and is working well. try more.