This discussion has been locked.

You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Interrupts not working when USB IAP(AN10711) is used

Hi All,
I am not an expert on ARM yet but an average guy for uC.

I am trying to get hands on with LPC2148 and plan to use it in next project.

One wonderful thing that I came across (I come form a background where we use 8051/mega16 uC) is USB IAP. So without any UART/Serial cable, I can flash program just by using USB cable.

Did some changes like
1. generating bin file (using fromelf --bin ....) and
2. changing IROM1 from 0x0 to 0x2000

to make program work with IAP.

I tasted some program and those worked very well.

But the issue is arising when I try to use Timer0 interrupt.
I see controller getting stuck somewhere just after 1st int.

I checked with "Use Memory Layout with Target Dialog" selected and de-selected both.
Nothing worked.

This has something to do with vector table but I am not able to make out what?

Any help on this would be appreciated.

Remember, I just made 3 above mentioned changes after creating new project.
If there is anything else, please let me know.

Parents

0 Urvish Gohil over 13 years ago in reply to Tamiryan Michael

I think you misunderstood the issue.
I have 2 programs now.

1. USB_IAP.hex : loaded at location 0x0:0x1FFF
2. my_prog.bin : loaded from 0x2000:0x2100 via IAP.

Now my_prog.bin has already been loaded via IAP.

Now, when I reset the board, first IAP will run, but as entry to bootloader is not asserted, it will jump to my_prog.bin.

Now, my_prog.bin is using timer interrupt.
So, when my_prog.bin is running, (and IAP is not running), will I be able to use interrupt?

I checked the Startup.s file and couldn't figure out much.
I do not have code for USB_IAP.hex.
I have code of my_prog.bin.

Now, what changes will I have to make to make interrupt of my_prog.bin work.

Per, your inputs will be much appreciated.
Tamir, thanks to being with me on this.
Cancel
Vote up 0 Vote down

Cancel

Reply

0 Urvish Gohil over 13 years ago in reply to Tamiryan Michael

I think you misunderstood the issue.
I have 2 programs now.

1. USB_IAP.hex : loaded at location 0x0:0x1FFF
2. my_prog.bin : loaded from 0x2000:0x2100 via IAP.

Now my_prog.bin has already been loaded via IAP.

Now, when I reset the board, first IAP will run, but as entry to bootloader is not asserted, it will jump to my_prog.bin.

Now, my_prog.bin is using timer interrupt.
So, when my_prog.bin is running, (and IAP is not running), will I be able to use interrupt?

I checked the Startup.s file and couldn't figure out much.
I do not have code for USB_IAP.hex.
I have code of my_prog.bin.

Now, what changes will I have to make to make interrupt of my_prog.bin work.

Per, your inputs will be much appreciated.
Tamir, thanks to being with me on this.
Cancel
Vote up 0 Vote down

Cancel

Children

0 John Linq over 13 years ago in reply to Urvish Gohil

Urvish Gohil => Now, what changes will I have to make to make interrupt of my_prog.bin work.

Per => A program that is loaded at a different place need to remap the interrupt vector table. There are settings in the startup file to do this - copying the interrupt vector table into RAM and remap to that address. Without remapping, the processor would search for an interrupt handler within your boot loader code.

On the Startup file of my_prog.bin:
Set Options-> Asm-> Conditional Assembly Control Symbols: RAM_INTVEC REMAP RAM_MODE

And check what RAM_INTVEC REMAP RAM_MODE will do for you.
Cancel
Vote up 0 Vote down

Cancel
0 Urvish Gohil over 13 years ago in reply to John Linq

Thanks John for that wonderful and easy explanation.
While I did get what Per said, but didn't know how to do it.

Right now I do not have access to the board.
Will post here the my observation as soon as I get it(Hope to keep some smileys than).
Cancel
Vote up 0 Vote down

Cancel
0 Urvish Gohil over 13 years ago in reply to Urvish Gohil

Hi John,
I just tried adding "RAM_INTVEC REMAP RAM_MODE" but it didn't worked.

Here is what I tried.
1. I just wrote a prog in keil which toggles 2 port pins. 1st by a while loop, 2nd by timer.
2. Without adding anything I simulated it in keil. (IROM1 still from 0x0, No remapping)
3. This works well and I see both of the port pins toggling.

Now I made a simple change of Adding "RAM_INTVEC REMAP RAM_MODE".
I recompiled the code and simulated.
Here, I saw that, as soon as int is occurred, LPC jumps to "LDR PC, [PC, #-0x0FF0]", but does not move from that point.

Moreover, I see words REMAP and RAM_MODE in Startup.s but not the RAM_INTVEC.
I am using Startup.s provided by keil only.
Cancel
Vote up 0 Vote down

Cancel
0 John Linq over 13 years ago in reply to Urvish Gohil
KEIL has quite a lot startup.s/LPCooxx.s
You need another startup.s like this:
rtime.felk.cvut.cz/.../lpc21xx-boot

+# Memory Mapping (when Interrupt Vectors are in RAM) + .equ MEMMAP, 0xE01FC040 /* Memory Mapping Control */ +.ifdef RAM_INTVEC + LDR R0, =MEMMAP + MOV R1, #2 + STR R1, [R0] +.endif
Cancel
Vote up 0 Vote down

Cancel

0 Urvish Gohil over 13 years ago in reply to John Linq

I think what I have is exactly this only.

; Memory Mapping (when Interrupt Vectors are in RAM)
MEMMAP          EQU     0xE01FC040      ; Memory Mapping Control
                IF      :DEF:REMAP
                LDR     R0, =MEMMAP
                IF      :DEF:EXTMEM_MODE
                MOV     R1, #3
                ELIF    :DEF:RAM_MODE
                MOV     R1, #2
                ELSE
                MOV     R1, #1
                ENDIF
                STR     R1, [R0]
                ENDIF

By defining REMAP and RAM_MODE, this will do exactly what your code snippets does with RAM_INTVEC.

In the Startup.s that I am using, what shown above is the only place where REMAP and RAM_MODE is used. There are no other defines.

0 John Linq over 13 years ago in reply to Urvish Gohil

I guess your startup.s is very like this one:

forum.sparkfun.com/viewtopic.php

If so, you need to figure out how it accomplishes what Per told you.

And, I don't think you can easily simulate USB_IAP.hex + my_prog.bin, it would be easier to run them on the real hardware.
Cancel
Vote up 0 Vote down

Cancel
0 John Linq over 13 years ago in reply to John Linq

Are you using this:
ics.nxp.com/.../
==> Boot Loader V2.12 for LPC213x and LPC214x (Apr 12, 2007)
And it does not provide source code for bootloader (USB_IAP.hex)?
Cancel
Vote up 0 Vote down

Cancel
0 John Linq over 13 years ago in reply to John Linq

Take a look at this: it is for LPC23xx.
http://www.keil.com/forum/13707/

See if you can debug your my_prog.bin like the below.
After all of that, I start my Debug Session. The Disassembly Window shows the Machine Code/ASM Code of the Bootloader (without the Source Code). Then, the Bootloader jumps to my application. So that, I get the state while the Bootloader just finishes its work, and pass the control to my application. I can observe the CPSR and the R13/SP of Supervisor Mode etc, to see if the solutions works properly.
Cancel
Vote up 0 Vote down

Cancel
0 Urvish Gohil over 13 years ago in reply to John Linq

John,
I did try the changes on hardware also. Yes, you are correct that simulation cannot be always correct.

BTW, I didn't find this connected to this issue.
"Are you using this:

USB_IAP.hex is going to be the secondary bootloader which resides in 128k flash.
And, as far as I understand, the link you gave is for primary bootloader which is by default by NXP.

Here is what I am using
"">www.nxp.com/search

BTW,
Right now I am looking at "http://www.keil.com/forum/13707/" which you gave.
Though this tread is for different uC and App Not is also different (AN10759), I think the idea should be same.

Thanks for the pointer. Will have a look at it and post the conclusion here.

Meanwhile, if there is something new, I would be glad to take it.
Cancel
Vote up 0 Vote down

Cancel
0 John Linq over 13 years ago in reply to Urvish Gohil

www.nxp.com/.../LPC2000_Series_Secondary_Bootloader.zip
Cancel
Vote up 0 Vote down

Cancel
0 John Linq over 13 years ago in reply to John Linq

The above link is not for USB_IAP either. I am sorry.
Cancel
Vote up 0 Vote down

Cancel
0 John Linq over 13 years ago in reply to John Linq

www.sparkfun.com/.../94

LPC2148 USB Bootloader Tutorial
by zagGrad | August 04, 2008 | 17 comments

This link should provide everything you need, except it may not be designed for your hardware, and it is not for KEIL toolchain.
Cancel
Vote up 0 Vote down

Cancel

0 John Linq over 13 years ago in reply to John Linq

.if (RAM_MODE==0)
/* Relocate .data section (Copy from ROM to RAM) */
                LDR     R1, =_etext
                LDR     R2, =_data
                LDR     R3, =_edata
                CMP     R2, R3
                BEQ     DataIsEmpty
LoopRel:        CMP     R2, R3
                LDRLO   R0, [R1], #4
                STRLO   R0, [R2], #4
                BLO     LoopRel
DataIsEmpty:
.endif

0 John Linq over 13 years ago in reply to John Linq

www.embeddedrelated.com/.../39585.php

Copying Interrupt vector table to RAM

It is for IAR toolchain.
Cancel
Vote up 0 Vote down

Cancel

0 John Linq over 13 years ago in reply to John Linq

 (9)     LDMIA   r8!,{r0-r7}     ; Load Vectors
(10)     STMIA   r9!,{r0-r7}     ; Store Vectors
(11)     LDMIA   r8!,{r0-r7}     ; Load secondary vector table
(12)     STMIA   r9!,{r0-r7}     ; Store secondary vector table
         ; Setup Memory Mapping Control to remap the RAM vector area
(13)     LDR     r0,=LPC231X_MEMMAP
(14)     MOV     r1,#2           ; MEMMAP to User RAM mode
(15)     STRNE   r1,[r0,#0]      ; Remap Memory, if not remapped already