Reading from a Vendor Defined HID device

The sniffer catches low-level USB traffic, before the PC HID driver examines the packets.

a) PC HID driver drops the packets, because the packet format doesn't match to those on the report descriptor.

OR

b) Your PC application doesn't read the packets quick enough.

1) Post the report descriptor
2) Post the PC application code, around CreateFile() and ReadFile()



> how do i know if the hardware support "HidD_GetInputreport" function?

HidD_GetInputreport() reads packet over the default endpoint, by Get_Report request.
It can't read from the interrupt IN endpoint.

Tsuneo

The sniffer catches low-level USB traffic, before the PC HID driver examines the packets.

a) PC HID driver drops the packets, because the packet format doesn't match to those on the report descriptor.

OR

b) Your PC application doesn't read the packets quick enough.

1) Post the report descriptor
2) Post the PC application code, around CreateFile() and ReadFile()



> how do i know if the hardware support "HidD_GetInputreport" function?

HidD_GetInputreport() reads packet over the default endpoint, by Get_Report request.
It can't read from the interrupt IN endpoint.

Tsuneo

Here is the report descriptor

Usage Page: 06 00 FF
Usage: 09 01
Collection: A1 01 Report ID: 85 01 Usage: 09 00 Logical Min: 15 00 Logical Max: 26 FF 00 Report Size: 75 08 Report Count: 95 0D Input: 81 02 Usage: 09 00 Logical Min: 15 00 Logical Max: 26 FF 00 Report Size: 75 08 Report Count: 95 06 Output: 91 02
End Collection C0

The following codes are run in a thread
Source code:
hHandle = CreateFile(hDevice->DevicePath, GENERIC_READ, FILE_SHARE_READ | FILE_SHARE_WRITE, NULL, OPEN_EXISTING, FILE_ATTRIBUTE_NORMAL, NULL);

while(1)
{ Result = ReadFile( hHandle, buffer, // unsigned char *buffer = new unsigned char[256] capLength, // read from "HidP_GetCaps" and it is 14 (0x0E) &NumberOfBytesRead, // always return 0 but the data received is correct NULL );

if (Result) print out the received frame number WaitForSingleObject(hEventObject,50); ResetEvent(hEventObject);
}

Output:
1 2
(delay 500ms)
3 4
(delay 500ms)
...
10
11
(delay 500ms)
...

1) Report format
Your report descriptor is

Usage Page    : 06 00 FF
Usage         : 09 01
Collection    : A1 01

Report ID     : 85 01

Usage         : 09 00
Logical Min   : 15 00
Logical Max   : 26 FF 00
Report Size   : 75 08
Report Count  : 95 0D
Input         : 81 02

Usage         : 09 00
Logical Min   : 15 00
Logical Max   : 26 FF 00
Report Size   : 75 08
Report Count  : 95 06
Output        : 91 02

End Collection: C0

This report descriptor defines single input and single output report.
The format of each packet is,

Input report
 byte offset
    0     report ID (1)
  1 - 13  report body (13 bytes)

Output report
 byte offset
    0     report ID (1)
  1 - 6   report body (6 bytes)

Your firmware has to send 14 bytes input report packet, starting with report ID(1).
If the packet size wouldn't be 14 bytes, or if the packet wouldn't start with 1,
PC HID driver drops such a packet.

If you wouldn't have any plan to extend the report descriptor to exchange another size of input or output report, you may delete the Report ID definition from your report descriptor. And then, the report ID field is deleted from the input and report packets.

2) PC code
hHandle = CreateFile(hDevice->DevicePath, GENERIC_READ, FILE_SHARE_READ | FILE_SHARE_WRITE, NULL, OPEN_EXISTING, FILE_ATTRIBUTE_NORMAL, NULL);

CreateFile opens the device synchronously (non-OVERLAPPED).
It means, ReadFile doesn't return until it gets an input report.

I'm not sure, what is WaitForSingleObject() waiting.
If it would wait for ReadFile completion, it should be useless, because ReadFile returns just when it completes.

Tsuneo

Thanks for the detailed explanation on the report descriptor!

As you said the "ReadFile" will wait until the it get the input report. Yes, it is true. Those 500ms delay time is mostly on running "ReadFile" function. Does Bulk and Interrupt Transfer help this situation because I findthat USBlyze could read those data without 500ms delay. Or is there any tricky thing to deal with "ReadFile" function? Or It is the limitation set up by Windows?

Thanks!

Danny

Just delete WaitForSingleObject().
Maybe, it makes the trouble.

Tsuneo