• State Not Answered
  • Locked Locked
  • Replies 9 replies
  • Subscribers 21 subscribers
  • Views 2432 views
  • Users 0 members are here
2025 survey

We are running a survey to help us improve the experience for all of our members. If you see the survey appear, please take the time to tell us about your experience if you can.

Options
Related
How was your experience today?
This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Matlab to 8051 communication

SRI RAMANA

Hai...i tried to send the letter 'L','S','R' from matlab just opening in command line and typing...

se=serial('COM7');
set(se,'BaudRate',9600);
fopen(se);
fprintf(se,'%c','L','async');
fclose(se)

in matlab uc(at89c51)...and in response it should change its port settings accordingly...
Here is my code...

#include<reg51.h>
sbit mlp=P1^0;
sbit mln=P1^1;
sbit mrp=P1^2;
sbit mrn=P1^3;
void main(void)
{
  char i;
  SCON=0x50;  // to receive and transmitt serially
  TMOD=0x20;   // timer in mode 2 8 bit auto reload mode
   TH1=-3;   // baud rate 9600
   TR1 = 1;
   while(1)
     {
           if(TI==1)
                        TI=0;

                else if(RI ==1)
                        {
                                i=SBUF;
                                RI=0;
                        }
                if(i=='S')
                {
                mlp=mrp=1;
                mrn=mln=0;
                }
                else if(i=='L')
                {
                mlp=mrn=1;
                mrp=mln=0;
                }
                else if(i=='R')
                {
                mlp=mrn=0;
                mrp=mln=1;
                }
                else
                {
                mlp=mrn=0;
                mrp=mln=0;
                }
           }


}


I have my uc connections on bread board...and i dnt knw wat is the Tx,Rx pin in my connector...
So what i did was put a 2k Resistor in between so that not to fry the ckt accidentatally in case i changed the pins...the character is not at all being sent...the four pins are in 0 condition...see the ELSE part...in abv prgm... Please help... re soon...please....

Parents Reply Children
  • 0 in reply to Andy Neil

    thank u for replying...now is this program okay???

    #include<reg51.h>
sbit mlp=P1^0;
sbit mln=P1^1;
sbit mrp=P1^2;
sbit mrn=P1^3;
void main(void)
{
  char i='\0';
  SCON=0x50;  // to receive and transmitt serially
  TMOD=0x20;   // timer in mode 2 8 bit auto reload mode
   TH1=-3;   // baud rate 9600
   TR1 = 1;
   while(1)
     {

           if(TI==1)
                {       TI=0;


                        }
                else if(RI ==1)
                        {
                                i=SBUF;

                if(i=='S')
                {
                mlp=mrp=1;
                mrn=mln=0;
                }
                else if(i=='L')
                {
                mlp=mrn=1;
                mrp=mln=0;
                }
                else if(i=='R')
                {
                mlp=mrn=0;
                mrp=mln=1;
                }
                else
                {
                mlp=mrn=0;
                mrp=mln=0;
                }
                RI=0;

                        }




           }
}


    i still dint get the o/p...i have a cheap usb to serial converter along with transreceiver and my friend said he even did interrupts with this cable....so i dnt tink that wd be a problem....
    and i didnt chk o/p of serial com still to do....tel me f dis prog is okay??? also for serial communication do we have to mess with dat ale and psen pins...or anything out of ordinary u wd do for normal line follower???

  • 0 in reply to SRI RAMANA

    also please note that all the above program...simulated prefectly in keil....

  • 0 in reply to SRI RAMANA

    dnt tink wd chk tel f dis prog dat u wd

    I will copy your idea saving on typing and type 'no' instead of 'yes'

    Erik