• State Not Answered
  • Locked Locked
  • Replies 8 replies
  • Subscribers 21 subscribers
  • Views 4693 views
  • Users 0 members are here
2025 survey

We are running a survey to help us improve the experience for all of our members. If you see the survey appear, please take the time to tell us about your experience if you can.

Options
Related
How was your experience today?
This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Bootloader: Flash Download Failed

Lillian XU

HI All,

I compile the DFU example from ST using Keil MDK and try to download it into Bank 1. I always get a error: Flash Download failed -- ARM966E-S(I am using STR912FAW44). The following is what I do:

I setup the uVISION IDE the same as the thread http://www.keil.com/support/docs/3347.htm

Setup FMI in str91x.s


FMI_SETUP       EQU     1
FMI_CR_Val      EQU     0x00000018
FMI_BBSR_Val    EQU     0x00000000
FMI_BBADR_Val   EQU     0x00000000
FMI_NBBSR_Val   EQU     0x00000006
FMI_NBBADR_Val  EQU     0x00400000
FLASH_CFG_Val   EQU     0x00000000

Setup STR91xCFG.s


CFG             EQU     1
CFG_W0          EQU     0x00000000
CFG_W1          EQU     0x00010000

What am I missing in my project setting?

Thanks

Lillian

Parents
  • 0 in reply to Stuart Wright

    Hi Stuart,

    When I compile the STR91x flash file using keil MDK, i got the three warning message.


    Build target 'STR91xFxx4 Bank1 ICP'
    compiling FlashDev.c...
    linking...
    STR91xFxx4B1.axf: Warning: L6305W: Image does not have an entry point. (Not specified or not set due to multiple choices.)
    .\TargetX.lin(12): warning: L6314W: No section matches pattern *(RW).
    .\TargetX.lin(12): warning: L6314W: No section matches pattern *(ZI).
    Program Size: Code=0 RO-data=4256 RW-data=0 ZI-data=0
    User command #1: cmd.exe /C copy STR91xFxx4B1.axf ..\STR91xFxx4B1_.FLX 1 file(s) copied.
    "STR91xFxx4B1.axf" - 0 Error(s), 3 Warning(s).

    I wonder if the warning message affect the downloading.

    Thanks

    Lillian

Reply
  • 0 in reply to Stuart Wright

    Hi Stuart,

    When I compile the STR91x flash file using keil MDK, i got the three warning message.


    Build target 'STR91xFxx4 Bank1 ICP'
    compiling FlashDev.c...
    linking...
    STR91xFxx4B1.axf: Warning: L6305W: Image does not have an entry point. (Not specified or not set due to multiple choices.)
    .\TargetX.lin(12): warning: L6314W: No section matches pattern *(RW).
    .\TargetX.lin(12): warning: L6314W: No section matches pattern *(ZI).
    Program Size: Code=0 RO-data=4256 RW-data=0 ZI-data=0
    User command #1: cmd.exe /C copy STR91xFxx4B1.axf ..\STR91xFxx4B1_.FLX 1 file(s) copied.
    "STR91xFxx4B1.axf" - 0 Error(s), 3 Warning(s).

    I wonder if the warning message affect the downloading.

    Thanks

    Lillian

Children
  • 0 in reply to Lillian XU

    Lillian,

    I made the changes and just tried compiling this here using MDK 4.14. I didn't get any warnings see below.

    
Build target 'STR91xFxx4 Bank1 ICP'
compiling FlashDev.c...
linking...
Program Size: Code=0 RO-data=4256 RW-data=4 ZI-data=0
User command #1: cmd.exe /C copy STR91xFxx4B1.axf ..\STR91xFxx4B1_.FLX
        1 file(s) copied.
"STR91xFxx4B1.axf" - 0 Error(s), 0 Warning(s).

    I have uploaded the file for you at

    www.filedropper.com/str91xfxx4b1

    So you can try this one if you want

    Regards,

    Stuart.

  • 0 in reply to Stuart Wright

    Hi Stuart,

    Thank you for your kind help. I try your file and still get the programming failed. I check the chip version in my MCBSTR9 board is G. Also, could you please do me a favour to take a look at my STR91x flash file and see why i get the warning message. I find it cannot attatch file here. Could you please sene me the email lillian201151@hotmail.com so I can send you my design file?

    Thanks a lot

    Lillian

  • 0 in reply to Lillian XU

    Hi,

    I find the reason to fail program.
    Go to Options for Target -> Debug -> Ulink ARM Debugger Settings -> MAX JTAG Clock

    Change MAX JTAG Clock from 1M to 500K.

    Then flash program will be successful.

    Best Regards,

    Lillian