How to intialize TFT LCD using spi communication

1) Why not start your own thread, instead of piggybacking on an existing thread?

2) How much work have you done on your own, before posting your help request?

3) In which way are you supposted to develop the code?

1) Why not start your own thread, instead of piggybacking on an existing thread?

2) How much work have you done on your own, before posting your help request?

3) In which way are you supposted to develop the code?

Thanks for ur reply Per Westermark.
1.I came across the forum from google and found that Paval alrady finished the coding. So just continuned the discussion so that i get his contact.
2.I am trying to implement TFT with HX8238 driver in SPI.
3.Studied the datasheet and followed the sequence said in that to initilize the TFT.
>I used SPI @ 10Mhz and DataLatch at rising edge of the clock.8bit communication
>data were sent in 2 set, First is the Deveice ID(011100RsRW)followed by address
>Then same deveice ID followed by data.
Plase find my code below
-----------------------------------------
void Init_TFT(void){ TFT_Reset=1; delay_msec(60); TFT_Reset=0; delay_msec(60); TFT_Reset=1; delay_msec(300);

TFT_Srl_Send(0x72,0x01,0x6300); TFT_Srl_Send(0x72,0x02,0x0200); TFT_Srl_Send(0x72,0x03,0x7184); delay_msec(125); TFT_Srl_Send(0x72,0x04,0x0447);
TFT_Srl_Send(0x72,0x05,0xB4D4); TFT_Srl_Send(0x72,0x0A,0x4008); delay_msec(50);

TFT_Srl_Send(0x72,0x0B,0xD400); TFT_Srl_Send(0x72,0x0D,0x1235); delay_msec(250);

TFT_Srl_Send(0x72,0x0E,0x2B00); delay_msec(250);

TFT_Srl_Send(0x72,0x0F,0x0000); TFT_Srl_Send(0x72,0x16,0x9F80); TFT_Srl_Send(0x72,0x17,0x2212); delay_msec(250);

TFT_Srl_Send(0x72,0x1E,0x00DB); delay_msec(250);

TFT_Srl_Send(0x72,0x30,0x0507); TFT_Srl_Send(0x72,0x31,0x0004); TFT_Srl_Send(0x72,0x32,0x0707); TFT_Srl_Send(0x72,0x33,0x0000); TFT_Srl_Send(0x72,0x34,0x0000); TFT_Srl_Send(0x72,0x35,0x0307); TFT_Srl_Send(0x72,0x36,0x0700); TFT_Srl_Send(0x72,0x37,0x0000); TFT_Srl_Send(0x72,0x3A,0x0000); TFT_Srl_Send(0x72,0x3B,0x0000); delay_msec(250);

}

void TFT_Srl_Send(unsigned char Reg_Add,unsigned char Int_Add,unsigned short Data) { unsigned char Lca_Cmd[3];

Lca_Cmd[0]=Reg_Add; Lca_Cmd[1]=0; Lca_Cmd[2]=Int_Add;

TFT_nChipSelect =0; DMA_SPI(&Lca_Cmd[0],3); Nop();Nop();Nop(); TFT_nChipSelect =1;

Lca_Cmd[0]=Reg_Add; Lca_Cmd[1]=(Data&0xFF00)>>8; Lca_Cmd[2]=(Data&0xFF);

TFT_nChipSelect =0; DMA_SPI(&Lca_Cmd[0],3); Nop();Nop();Nop(); TFT_nChipSelect =1;
} //-----------------------------------//

I wish to know how to load the data to the pixels. I have used Parallel communication earlier, were i can select instruction/data using an IO and latch data to
the parallel data pin. I dont know how to do the same in this SPI

Doesn't the Datasheet tell you that?

This forum clearly tells you how to post source code:
www.danlhenry.com/.../keil_code.png

If you managed to miss that, you've probably also missed important details in the Datasheet - so go back and really study it carefully...