• State Not Answered
  • Locked Locked
  • Replies 7 replies
  • Subscribers 21 subscribers
  • Views 1686 views
  • Users 0 members are here
2025 survey

We are running a survey to help us improve the experience for all of our members. If you see the survey appear, please take the time to tell us about your experience if you can.

Options
Related
How was your experience today?
This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

interrupt on uart 0 hangs

rupesh vishwakarma

I am using ARM STR9 board
when I use
UART_ITConfig(UART0,UART_IT_Receive,ENABLE);

and after that I use a while loop and print hello on the screen

problem is that programme jumps to ISR but it hangs there it does not comes back #include "91x_lib.h"

#include "stdio.h"
#define TxBufferSize (countof(TxBuffer) - 1)
#define RxBufferSize 0x0A
#define countof(a) (sizeof(a) / sizeof(*(a)))
u8 TxBuffer[] = "UART Example1: UART - Hyperterminal communication using hardware flow control\n\r"; u8 RxBuffer[RxBufferSize]; u8 NbrOfDataToTransfer = TxBufferSize; u8 TxCounter = 0; u8 RxCounter = 0;
bool flag=0; static void Delay(u32 nCount)
{ u32 j = 0;

for(j = nCount; j != 0; j--);
} void main(void)
{ GPIO_InitTypeDef GPIO_InitStructure; UART_InitTypeDef UART_InitStructure;

SCU_APBPeriphClockConfig(__UART0, ENABLE); SCU_APBPeriphClockConfig(__GPIO5, ENABLE); // SCU->GPIOOUT[9] = 0x5555;

SCU_APBPeriphClockConfig(__GPIO9, ENABLE); SCU->GPIOOUT[9] = 0xFFFF; GPIO9->DDR = 0xFF; GPIO9->DR[0x3FC] = 0xFF;

GPIO_DeInit(GPIO5); GPIO_InitStructure.GPIO_Direction = GPIO_PinInput; GPIO_InitStructure.GPIO_Pin = GPIO_Pin_1; GPIO_InitStructure.GPIO_Type = GPIO_Type_PushPull ; GPIO_InitStructure.GPIO_IPConnected = GPIO_IPConnected_Enable; GPIO_InitStructure.GPIO_Alternate = GPIO_InputAlt1 ; GPIO_Init (GPIO5, &GPIO_InitStructure);

GPIO_InitStructure.GPIO_Direction = GPIO_PinOutput; GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0; GPIO_InitStructure.GPIO_Type = GPIO_Type_PushPull ; GPIO_InitStructure.GPIO_Alternate = GPIO_OutputAlt3 ; GPIO_Init (GPIO5, &GPIO_InitStructure);

UART_DeInit(UART0); UART_InitStructure.UART_WordLength = UART_WordLength_8D; UART_InitStructure.UART_StopBits = UART_StopBits_1; UART_InitStructure.UART_Parity = UART_Parity_No ; UART_InitStructure.UART_BaudRate = 115200; UART_InitStructure.UART_HardwareFlowControl = UART_HardwareFlowControl_None; UART_InitStructure.UART_Mode = UART_Mode_Tx_Rx; UART_InitStructure.UART_FIFO = UART_FIFO_Disable; UART_Init(UART0, &UART_InitStructure); UART_ITConfig(UART0,UART_IT_Receive,ENABLE); UART_Cmd(UART0, ENABLE);

SCU_AHBPeriphClockConfig(__VIC,ENABLE); VIC_DeInit(); //VIC Configuration // VIC_Config(UART0_ITLine,VIC_IRQ , 0); VIC_ITCmd(UART0_ITLine, ENABLE); while(1) { if(flag==0) printf("HELLO"); }

}

int SendChar (int ch)
{ UART_SendData(UART0, ch); while(UART_GetFlagStatus(UART0, UART_FLAG_Busy) != RESET); return (ch);
}

int GetKey (void)
{

}
void UART0_IRQHandler(void)
{ flag=1; do { if((UART_GetFlagStatus(UART1, UART_FLAG_RxFIFOEmpty) != SET)&&(RxCounter < RxBufferSize)) { RxBuffer[RxCounter] = UART0->DR; // UART_SendData(UART0, RxBuffer[RxCounter++]); // printf("ABCD"); } flag=0; }while((RxBuffer[RxCounter-1] != '\r')&&(RxCounter != RxBufferSize)); UART_ITConfig(UART0, UART_IT_Receive,DISABLE);
// VIC0->INTECR=0xFFFF;

}

can anyone suggest the code for interrupt driven uart for STR912 board

Parents
  • 0 in reply to rupesh vishwakarma

    I did not write "Please repost".

    I did write "Please repost, but this time follow the description printed directly above the text input box."

    If I follow the instructions, and post code, it looks like this:

    #include <stdio.h>

int main(void) {
    unsigned i;
    for (i = 0; i < 10; i++) {
        printf("i = %u\n",i);
    }
    return 0;
}


    Why don't your code look the same - you did follow the posting instructions, didn't you?

Reply
  • 0 in reply to rupesh vishwakarma

    I did not write "Please repost".

    I did write "Please repost, but this time follow the description printed directly above the text input box."

    If I follow the instructions, and post code, it looks like this:

    #include <stdio.h>

int main(void) {
    unsigned i;
    for (i = 0; i < 10; i++) {
        printf("i = %u\n",i);
    }
    return 0;
}


    Why don't your code look the same - you did follow the posting instructions, didn't you?

Children
No data