This discussion has been locked.

You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Problem translating application to 0x8000 for debugging

I am trying to get Mon51 working at address 0x0000 in EPROM. Monitor is built with XDATA(XDATA_AREA(0D000H)), CODE(INITSEG(00000H)), INSTALLCODE(01000H).

Interrupt vectors are translated to 0x8000 except
the serial interrupt vector used by the monitor.

C:0x0000	020100	LJMP	C:0100

At C:0x0100 Code from Install.A51(InitSerial) runs
then
LJMP MON51 assembles as LJMP C:0546

C:0x0546	758107	MOV	SP(0x81),#0x07
C:0x0549	90D008	MOV	DPTR, #0xD008
C:0x054C	E4	CLR	A
C:0x054D	7805	MOV	R0,#05
C:0x054F	F0	MOVX	@DPTR,A
C:0x0550	A3	INC	DPTR
C:0x0551	8DFC	DJNZ	R0,C:054F
C:0x0553	7480	MOV	A,#P0(0x80)
C:0x0555	F0	MOVX	@DPTR,A
C:0x0556	A3	INC	DPTR
C:0x0557	7400	MOV	A,#0x00
C:0x0559	F0	MOVX	@DPTR,A
C:0x055A	A3	INC	DPTR
C:0x055B	7407	MOV	A,#0x07
C:0x055D	F0	MOVX	@DPTR,A

Executing this last step causes the debugger to pause for about 2 seconds, then the PC $= 0x8000

C:0x8000	LJMP	STARTUP1(C:9240)

This comes from STARTUP.A51 of my application which has a CSEG at 0x8000.

My target build has my application code starting at 0x9000.

At this point, I can start using the debugger correctly. I have full running, breakpoint, and debugging capability.

If I do not do the single stepping sequence up until the PC $ jumps to 0x8000 the debugger looses communications with the target, and a target reset is required. I cannot use the run until main() option.

Any help is appreciated.

Parents

0 Dave Fords over 21 years ago in reply to David Lively

By .MAP file is hope you mean .M51, here is the application code section

            * * * * * * *   C O D E   M E M O R Y   * * * * * * *
                    0000H     8000H                  *** GAP ***
            CODE    8000H     0003H     ABSOLUTE
                    8003H     0FFDH                  *** GAP ***
            CODE    9000H     00E9H     UNIT         ?C?LIB_CODE
            CODE    90E9H     0070H     UNIT         ?PR?_LCD_DISPLAY?LCDTEST
            CODE    9159H     003CH     UNIT         ?PR?HELLOWORLD?LCDTEST
            CODE    9195H     0036H     UNIT         ?CO?LCDTEST
            CODE    91CBH     002BH     UNIT         ?PR?LCD_INIT?LCDTEST
            CODE    91F6H     0025H     UNIT         ?PR?_DELAYMS?LCDTEST
            CODE    921BH     0025H     UNIT         ?PR?MAIN?LCDTEST
            CODE    9240H     000CH     UNIT         ?C_C51STARTUP

Here is the Code section from MON51.M51

            * * * * * * *   C O D E   M E M O R Y   * * * * * * *
            CODE    0000H     0043H     UNIT         INITSEG
                    0043H     00BDH                  *** GAP ***
            CODE    0100H     0030H     UNIT         INSTALLCODE
                    0130H     00D0H                  *** GAP ***
            CODE    0200H     0342H     PAGE         STOPSEG
            CODE    0542H     05BBH     UNIT         CODE_AREA
            CODE    0AFDH     0548H     UNIT         GOCODE_AREA

Reply

0 Dave Fords over 21 years ago in reply to David Lively

By .MAP file is hope you mean .M51, here is the application code section

            * * * * * * *   C O D E   M E M O R Y   * * * * * * *
                    0000H     8000H                  *** GAP ***
            CODE    8000H     0003H     ABSOLUTE
                    8003H     0FFDH                  *** GAP ***
            CODE    9000H     00E9H     UNIT         ?C?LIB_CODE
            CODE    90E9H     0070H     UNIT         ?PR?_LCD_DISPLAY?LCDTEST
            CODE    9159H     003CH     UNIT         ?PR?HELLOWORLD?LCDTEST
            CODE    9195H     0036H     UNIT         ?CO?LCDTEST
            CODE    91CBH     002BH     UNIT         ?PR?LCD_INIT?LCDTEST
            CODE    91F6H     0025H     UNIT         ?PR?_DELAYMS?LCDTEST
            CODE    921BH     0025H     UNIT         ?PR?MAIN?LCDTEST
            CODE    9240H     000CH     UNIT         ?C_C51STARTUP

Here is the Code section from MON51.M51

            * * * * * * *   C O D E   M E M O R Y   * * * * * * *
            CODE    0000H     0043H     UNIT         INITSEG
                    0043H     00BDH                  *** GAP ***
            CODE    0100H     0030H     UNIT         INSTALLCODE
                    0130H     00D0H                  *** GAP ***
            CODE    0200H     0342H     PAGE         STOPSEG
            CODE    0542H     05BBH     UNIT         CODE_AREA
            CODE    0AFDH     0548H     UNIT         GOCODE_AREA

Children

No data