• Locked Locked
  • Replies 8 replies
  • Subscribers 120 subscribers
  • Views 18346 views
  • Users 0 members are here
Options
Related
How was your experience today?
This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

ping failed; host 192.168.1.100 is not alive

murnesty lm
Note: This was originally posted on 5th May 2011 at http://forums.arm.com

My hyper terminal display:
Booting with TI UBL            
Device OPP (300MHz, 1.2V)                  

U-Boot 2009.11 (May 03 2010 - 15:38:40)                                

I2C:   ready        
DRAM:  64 MB        
In: serial      
Out:   serial      
Err:   serial      
ARM Clock : 300000            
DDR Clock : 132000000 Hz                    
Net:   Ethernet PHY: GENERIC @ 0x00                            

Hit any key to stop autoboot:  0                            
U-Boot > print
bootargs=mem=32M console=ttyS2,115200n8 root=/dev/mmcblk0p1 rw rootwait ip=off
bootcmd=sf probe 0;sf read 0xc0700000 0x80000 0x220000;bootm 0xc0700000
baudrate=115200
bootfile="uImage"
dlbuff=0xc0400000
kerneladdr=0x00080000
bootdelay=6
ipaddr=192.168.1.100
serverip=192.168.1.100
dnsip=202.188.1.5
ethaddr=00:25:11:03:47:10
netmask=255.255.255.0
gatewayip=192.168.1.1
stdin=serial
stdout=serial
stderr=serial
ver=U-Boot 2009.11 (May 03 2010 - 15:38:40)

Environment size: 454/65532 bytes
U-Boot > ping 192.168.1.100
Using  device
ping failed; host 192.168.1.100 is not alive
U-Boot >

I connected my serial port and network cable. It did not show any error or warning... but yet cant connect.. anyone can tell me the reason?
Parents
  • Note: This was originally posted on 16th May 2011 at http://forums.arm.com

    So, i assign the serverip to my pc IP and then ipaddr as board ip...

    so is like :
    serverip = 192.168.1.100
    ipaddr = 192.168.1.1

    then i tried ping 192.168.1.1 and ping 192.168.1.100. But both also ping not alive.

    I was connect the board only check ipconfig /all . Then it display DNS servers as 202.188.1.5.
    My board ethernet port has LED flashing green / yellow when i turn on my board.

    I also attached a picture from the user manual i had. It show using device is normal. If you want the whole pdf here then i will post later.
Reply
  • Note: This was originally posted on 16th May 2011 at http://forums.arm.com

    So, i assign the serverip to my pc IP and then ipaddr as board ip...

    so is like :
    serverip = 192.168.1.100
    ipaddr = 192.168.1.1

    then i tried ping 192.168.1.1 and ping 192.168.1.100. But both also ping not alive.

    I was connect the board only check ipconfig /all . Then it display DNS servers as 202.188.1.5.
    My board ethernet port has LED flashing green / yellow when i turn on my board.

    I also attached a picture from the user manual i had. It show using device is normal. If you want the whole pdf here then i will post later.
Children
No data