Sun 31 Jul 22:52:10 BST 2022 1) I have produced a bootable USB mem stick cm770@pursuit2:/camb/carloscheri$ lsblk ... sdb 8:16 0 465.8G 0 disk └─sdb1 8:17 0 465.8G 0 part /camb sdc 8:32 1 58.2G 0 disk sr0 11:0 1 1024M 0 rom cm770@pursuit2:/camb/carloscheri$ sudo dd if=cheribsd-memstick-arm64-aarch64c-22.05p1.img of=/dev/sdc conv=fsync bs=1M [sudo] password for cm770: 777+1 records in 777+1 records out 814955008 bytes (815 MB, 777 MiB) copied, 124.943 s, 6.5 MB/s 2) sync cm770@pursuit2:/camb/carloscheri$ sync 3) I have upgraded the Morello board internal SDcard cm770@pursuit2:/$ lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT sdc 8:32 1 1.9G 0 disk └─sdc1 8:33 1 1.9G 0 part /media/cm770/M1SDP 3.1) mount SDcard cm770@pursuit2:/$ sudo mount /dev/sdc1 /mnt [sudo] password for cm770: cm770@pursuit2:~$ sudo mount /dev/sdc1 /mnt cm770@pursuit2:~$ ls /mnt config.txt ee0364b.txt LIB LICENSES MB SOFTWARE 3.2) Remove old files from SDcard cm770@pursuit2:~$ sudo rm -R /mnt/* 3.3 Copy new files to SDcard cm770@pursuit2:~$ sudo cp -rf /camb/carloscheri/board-firmware-morello-mainline/* /mnt cm770@pursuit2:~$ ls -l /mnt total 192 -rwxr-xr-x 1 root root 1199 Jul 31 23:24 config.txt -rwxr-xr-x 1 root root 215 Jul 31 23:24 ee0364b.txt drwxr-xr-x 2 root root 32768 Jul 31 23:24 LIB drwxr-xr-x 5 root root 32768 Jul 31 23:24 LICENSES drwxr-xr-x 3 root root 32768 Jul 31 23:24 MB drwxr-xr-x 2 root root 32768 Jul 31 23:24 SOFTWARE cm770@pursuit2:~$ sync 3.4 umount SDcard to prevent corruption cm770@pursuit2:~$ sudo umount /dev/sdc1 4) I have plugged to bootable USB stick to one of the USB ports of the Morello board and turned it ON Cmd> Arm M1SDP MCC Boot loader v1.0.0 HBI0364 build 534 MCC: Power On MCC to access SD card request acknowledged. Clear ULINK JTAG Time : 22:27:25 Date : 31:07:2022 Arm M1SDP MCC Firmware v2.3.0 Build Date: Apr 19 2022 Powering up system... MCC to access SD card request acknowledged. Clear ULINK JTAG Time : 22:27:32 Date : 31:07:2022 Switching on ATXPSU... Switching on main power... 12V Rail Check Pass Reading Board File \MB\HBI0364B\io_v010f.txt TOTAL OSCCLKS: 15 PMIC RAM configuration (80_1_86G.bin)... Temperature (deg C) Outlet = 30.9 PMIC = 39.1 SoC = 37.1 IN2 = 33.9 IN1 = 32.9 MidBrd = 39 PCIeSW = 41 MCC = 36.2 FPGA = 35.0 SoC Fan Speed = 9% ALERT off Configuring motherboard (rev B, var A)... Configuring FPGA from file \MB\HBI0364B\io_v010f.bit Address: 0x007E0000 FPGA configuration complete. Config clocks num: 15 OSCCLK0 : 50.000000MHz OSCCLK1 : 50.000000MHz OSCCLK2 : 50.000000MHz OSCCLK3 : 50.000000MHz OSCCLK4 : 50.000000MHz OSCCLK5 : 50.000000MHz OSCCLK6 : 50.000000MHz OSCCLK7 : 50.000000MHz OSCCLK8 : 75.000000MHz OSCCLK9 : 85.000000MHz OSCCLK10 : 12.288000MHz OSCCLK11 : 50.000000MHz OSCCLK12 : 50.000000MHz OSCCLK13 : 50.000000MHz OSCCLK14 : 170.000000MHz OSCCLK setup: PASSED GTXCLK setup: PASSED EEPROM config found File to compare \MB\HBI0364B\pci_v002.bin \MB\HBI0364B\pci_v002.bin UPDATE IN PROGRESS PCIe PEX I2C configuration PCIe I2C R/W test passed... Reading PCIe EEPROM file \MB\HBI0364B\pci_v002.bin DMA TX Handler Address: 0x00000017 PCIe EEPROM programmed Writing SCC 0x014 with ACLK 50000000 Hz Writing SCC 0x00C with 0x00000003 Writing SCC 0x020 with 0x06090805 Writing SCC 0x024 with 0x06060606 Writing SCC 0x028 with 0x00000606 Writing SCC 0x1160 with 0x00000001 Writing SCC 0x1164 with 0x01000000 Writing SCC 0x1168 with 0x00000000 Writing SCC 0x116C with 0x00000000 Writing SCC 0x1180 with 0x00000000 Writing SCC 0x1184 with 0x0000000C Writing SCC 0x1188 with 0x00000000 Writing SCC 0x118C with 0x00000000 Writing SCC 0x1190 with 0x00000000 Writing SCC 0x1194 with 0x00000000 Writing SCC 0x1198 with 0x00000000 Writing SCC 0x119C with 0x00000000 Reading SCC 0xFF8 with 0x0A364A08 Reading SCC 0xFFC with 0x41050000 QSPI Controller detected id = 0x4000303 Device ID 0x20, 0xBB, 0x19 Setting QSPI dummy clocks... Dummy clocks already set Device ID 0x20, 0xBB, 0x19 QSPI Controller detected id = 0x4000303 Device ID 0x20, 0xBB, 0x19 Setting QSPI dummy clocks... Dummy clocks already set Device ID 0x20, 0xBB, 0x19 QSPI Controller detected id = 0x4000303 Device ID 0x20, 0xBB, 0x19 Setting QSPI dummy clocks... Dummy clocks already set Device ID 0x20, 0xBB, 0x19 Updating SCP qspi with PCC bios ...... File \MB\HBI0364B\pcc_v055.bin written to MCC memory address 0x65F00000 DMA TX Handler PCC Bios updated from \MB\HBI0364B\pcc_v055.bin Waiting for PCC to copy boot loader from QSPI... Powering down... MCC to access SD card request acknowledged. SPI Write command to PCC: register 3 cmd 0xD003 tx data 0x1 SPI Return data from PCC: register 3 cmd 0x2000 rx data 0x0 Resetting board. Clear ULINK JTAG Arm M1SDP MCC Boot loader v1.0.0 HBI0364 build 534 MCC: Power On MCC to access SD card request acknowledged. Clear ULINK JTAG Time : 22:28:15 Date : 31:07:2022 Powering up system... MCC to access SD card request acknowledged. Clear ULINK JTAG Time : 22:28:20 Date : 31:07:2022 Switching on ATXPSU... Switching on main power... 12V Rail Check Pass Reading Board File \MB\HBI0364B\io_v010f.txt TOTAL OSCCLKS: 15 PMIC RAM configuration (80_1_86G.bin)... Temperature (deg C) Outlet = 30.9 PMIC = 38.4 SoC = 35.1 IN2 = 32.9 IN1 = 32.2 MidBrd = 38 PCIeSW = 40 MCC = 36.2 FPGA = 35.0 SoC Fan Speed = 9% ALERT off Configuring motherboard (rev B, var A)... Configuring FPGA from file \MB\HBI0364B\io_v010f.bit Address: 0x007E0000 FPGA configuration complete. Config clocks num: 15 OSCCLK0 : 50.000000MHz OSCCLK1 : 50.000000MHz OSCCLK2 : 50.000000MHz OSCCLK3 : 50.000000MHz OSCCLK4 : 50.000000MHz OSCCLK5 : 50.000000MHz OSCCLK6 : 50.000000MHz OSCCLK7 : 50.000000MHz OSCCLK8 : 75.000000MHz OSCCLK9 : 85.000000MHz OSCCLK10 : 12.288000MHz OSCCLK11 : 50.000000MHz OSCCLK12 : 50.000000MHz OSCCLK13 : 50.000000MHz OSCCLK14 : 170.000000MHz OSCCLK setup: PASSED GTXCLK setup: PASSED EEPROM config found File to compare \MB\HBI0364B\pci_v002.bin \MB\HBI0364B\pci_v002.bin Writing SCC 0x014 with ACLK 50000000 Hz Writing SCC 0x00C with 0x00000003 Writing SCC 0x020 with 0x06090805 Writing SCC 0x024 with 0x06060606 Writing SCC 0x028 with 0x00000606 Writing SCC 0x1160 with 0x00000001 Writing SCC 0x1164 with 0x01000000 Writing SCC 0x1168 with 0x00000000 Writing SCC 0x116C with 0x00000000 Writing SCC 0x1180 with 0x00000000 Writing SCC 0x1184 with 0x0000000C Writing SCC 0x1188 with 0x00000000 Writing SCC 0x118C with 0x00000000 Writing SCC 0x1190 with 0x00000000 Writing SCC 0x1194 with 0x00000000 Writing SCC 0x1198 with 0x00000000 Writing SCC 0x119C with 0x00000000 Reading SCC 0xFF8 with 0x0A364A08 Reading SCC 0xFFC with 0x41050000 QSPI Controller detected id = 0x4000303 Device ID 0x20, 0xBB, 0x19 Setting QSPI dummy clocks... Dummy clocks already set Device ID 0x20, 0xBB, 0x19 QSPI Controller detected id = 0x4000303 Device ID 0x20, 0xBB, 0x19 Setting QSPI dummy clocks... Dummy clocks already set Device ID 0x20, 0xBB, 0x19 QSPI Controller detected id = 0x4000303 Device ID 0x20, 0xBB, 0x19 Setting QSPI dummy clocks... Dummy clocks already set Device ID 0x20, 0xBB, 0x19 Reading images file \MB\HBI0364B\images.txt Updating MCP file File \SOFTWARE\mcp_fw.bin written to MCC memory address 0x64000000 DMA TX Handler Image: mcp_fw updated from \SOFTWARE\mcp_fw.bin Updating SCP file ...... File \SOFTWARE\scp_fw.bin written to MCC memory address 0x64000000 DMA TX Handler Image: scp_fw updated from \SOFTWARE\scp_fw.bin Updating AP QSPI file ....................................................................................... File \SOFTWARE\fip.bin written to MCC memory address 0x66000000 DMA TX Handler Image: fip updated from \SOFTWARE\fip.bin PCIe mac address = 0002 F70098FF PCC mac address = 0002 F70098FE LAN9221 was identified successfully. MAC addrs test: PASSED SMC MAC address 0002-F700-9900 Identifying DDR 0 Device Information Manufacturer ID = 80 2C Module Part Number = 9ASF1G72PZ-2G9E1 Module Serial Number = F2 E C2 0 Identifying DDR 1 Device Information Manufacturer ID = 80 2C Module Part Number = 9ASF1G72PZ-2G9E1 Module Serial Number = F2 E BF D8 Setting System LEDs[7:4] Setting PCIe_nPERST/PCIESW_PERSTN PCIe control C2C disabled APUART0 connected to USBPORT_3 SCPUART connected to USBPORT_4 MCPUART connected to USBPORT_5 PL031 Date & Time set = Sun Jul 31 22:29:18 2022 QSPI test (0x6403FEF8):0xFFFFFFFF Releasing SOC_nPOR/SOC_nSRST SPI Write command to PCC: register 3 cmd 0xD003 tx data 0x2 SPI Return data from PCC: register 3 cmd 0x2000 rx data 0x0 USB Serial Number = 500541683016 Cmd> 5) Show Firmware Cmd> ? Arm M1SDP MCC Firmware v2.3.0 Build Date: Apr 19 2022 Build Time: 13:40:34 + command ------------------+ function ---------------------------------+ | CAP "fname" [/A] | captures serial data to a file | | | [/A option appends data to a file] | | FILL "fname" [nnnn] | create a file filled with text | | | [nnnn - number of lines, default=1000] | | TYPE "fname" | displays the content of a text file | | REN "fname1" "fname2" | renames a file 'fname1' to 'fname2' | | COPY "fin" ["fin2"] "fout"| copies a file 'fin' to 'fout' file | | | ['fin2' option merges 'fin' and 'fin2'] | | DEL "fname" | deletes a file | | DIR "[mask]" | displays a list of files in the directory | | FORMAT [label] | formats Flash Memory Card | | USB_INIT | Re-initialize USB | | USB_ON | Enable usb | | USB_OFF | Disable usb | | SHUTDOWN | Shutdown PSU (leave micro running) | | REBOOT | Power cycle system and reboot | | RESET | Reset Board using CB_nRST | | IOFPGA_VERSION | Displays IOFPGA Version | | DEBUG | Enters debug menu | | EEPROM | Enters eeprom menu | | HELP or ? | displays this help | | | | THE FOLLOWING COMMANDS ARE ONLY AVAILABLE IN RUN MODE | | | | CASE_FAN_SPEED "SPEED" | SLOW, MEDIUM, FAST, 0%, 10%, 20%, .. 100% | | READ_AXI "fname" | Read system memory to file 'fname' | | "address" | from address to end address | | "end_address" | | | WRITE_AXI "fname" | Write file 'fname' to system memory | | "address" | at address | +---------------------------+-------------------------------------------+ Cmd> DIR MCC to access SD card request acknowledged. File System Directory... CONFIG.TXT 1.199 31.07.2022 22:24 EE0364B.TXT 215 31.07.2022 22:24 LIB -DIR- 31.07.2022 22:24 LICENSES -DIR- 31.07.2022 22:24 MB -DIR- 31.07.2022 22:24 TRASH-~1 -DIR- 08.06.2022 22:39 SOFTWARE -DIR- 31.07.2022 22:24 LOG.TXT 1.507 01.01.2016 12:00 3 File(s) 2.921 bytes 5 Dir(s) 1.994.489.856 bytes free. Cmd> USB_ON Enabling debug USB... Cmd> 6) I have tried to reboot from bootable USB stick. Cmd> reboot Rebooting... Disabling debug USB.. MCC to access SD card request acknowledged. Clear ULINK JTAG Board rebooting... Powering up system... MCC to access SD card request acknowledged. Clear ULINK JTAG Time : 22:32:36 Date : 31:07:2022 Switching on ATXPSU... Switching on main power... 12V Rail Check Pass Reading Board File \MB\HBI0364B\io_v010f.txt TOTAL OSCCLKS: 15 PMIC RAM configuration (80_1_86G.bin)... Temperature (deg C) Outlet = 30.9 PMIC = 41.9 SoC = 37.0 IN2 = 33.2 IN1 = 34.3 MidBrd = 42 PCIeSW = 49 MCC = 38.4 FPGA = 38.6 SoC Fan Speed = 9% ALERT off Configuring motherboard (rev B, var A)... Configuring FPGA from file \MB\HBI0364B\io_v010f.bit Address: 0x007E0000 FPGA configuration complete. Config clocks num: 15 OSCCLK0 : 50.000000MHz OSCCLK1 : 50.000000MHz OSCCLK2 : 50.000000MHz OSCCLK3 : 50.000000MHz OSCCLK4 : 50.000000MHz OSCCLK5 : 50.000000MHz OSCCLK6 : 50.000000MHz OSCCLK7 : 50.000000MHz OSCCLK8 : 75.000000MHz OSCCLK9 : 85.000000MHz OSCCLK10 : 12.288000MHz OSCCLK11 : 50.000000MHz OSCCLK12 : 50.000000MHz OSCCLK13 : 50.000000MHz OSCCLK14 : 170.000000MHz OSCCLK setup: PASSED GTXCLK setup: PASSED EEPROM config found File to compare \MB\HBI0364B\pci_v002.bin \MB\HBI0364B\pci_v002.bin Writing SCC 0x014 with ACLK 50000000 Hz Writing SCC 0x00C with 0x00000003 Writing SCC 0x020 with 0x06090805 Writing SCC 0x024 with 0x06060606 Writing SCC 0x028 with 0x00000606 Writing SCC 0x1160 with 0x00000001 Writing SCC 0x1164 with 0x01000000 Writing SCC 0x1168 with 0x00000000 Writing SCC 0x116C with 0x00000000 Writing SCC 0x1180 with 0x00000000 Writing SCC 0x1184 with 0x0000000C Writing SCC 0x1188 with 0x00000000 Writing SCC 0x118C with 0x00000000 Writing SCC 0x1190 with 0x00000000 Writing SCC 0x1194 with 0x00000000 Writing SCC 0x1198 with 0x00000000 Writing SCC 0x119C with 0x00000000 Reading SCC 0xFF8 with 0x0A364A08 Reading SCC 0xFFC with 0x41050000 QSPI Controller detected id = 0x4000303 Device ID 0x20, 0xBB, 0x19 Setting QSPI dummy clocks... Dummy clocks already set Device ID 0x20, 0xBB, 0x19 QSPI Controller detected id = 0x4000303 Device ID 0x20, 0xBB, 0x19 Setting QSPI dummy clocks... Dummy clocks already set Device ID 0x20, 0xBB, 0x19 QSPI Controller detected id = 0x4000303 Device ID 0x20, 0xBB, 0x19 Setting QSPI dummy clocks... Dummy clocks already set Device ID 0x20, 0xBB, 0x19 Reading images file \MB\HBI0364B\images.txt PCIe mac address = 0002 F70098FF PCC mac address = 0002 F70098FE LAN9221 was identified successfully. MAC addrs test: PASSED SMC MAC address 0002-F700-9900 Identifying DDR 0 Device Information Manufacturer ID = 80 2C Module Part Number = 9ASF1G72PZ-2G9E1 Module Serial Number = F2 E C2 0 Identifying DDR 1 Device Information Manufacturer ID = 80 2C Module Part Number = 9ASF1G72PZ-2G9E1 Module Serial Number = F2 E BF D8 Setting System LEDs[7:4] Setting PCIe_nPERST/PCIESW_PERSTN PCIe control C2C disabled APUART0 connected to USBPORT_3 SCPUART connected to USBPORT_4 MCPUART connected to USBPORT_5 PL031 Date & Time set = Sun Jul 31 22:32:55 2022 QSPI test (0x6403FEF8):0xFFFFFFFF Releasing SOC_nPOR/SOC_nSRST SPI Write command to PCC: register 3 cmd 0xD003 tx data 0x2 SPI Return data from PCC: register 3 cmd 0x2000 rx data 0x0 USB Serial Number = 500541683016 Cmd>