• Design Start ARM Cortex-M0

    vivek
    vivek

    Hi,

    I trying to build the peripheral around Cortex-M0 IP core thorugh AHB-lite system. Right now I have to integrate Cortex-M0 with the DDR2 SRAM (1Gb) through AHB lite.

    I searched on  internet which shows interfacing only through core generator (MIG…

    • Answered
    • over 6 years ago
    • Processors
    • Cortex-M / M-Profile forum
  • How to interface Accelerometer, EEPROM, GPS and GSM with Cortex-M?

    Suman Saurabh
    Suman Saurabh

    just help me out interfacing of GPS and GSM with Cortex-M?

    • Answered
    • over 5 years ago
    • System
    • Embedded forum
  • Trouble with read write on SD card

    Owais
    Owais

    Hello community members.

    I have recently started working with SD card using Microchip ARM based uC SAM4. So far I have managed to initialize the HSMCI interface of SAM4 and SD card is also initialized and has responded with the card capacity and the RCA…

    • over 5 years ago
    • System
    • Embedded forum
  • How to use GPIO interface IPs of ARM Cortex M0+

    Sabarish
    Sabarish

    Hello,

    We bought ARM CM0+ deliverables from ARM. I want to design an SoC which has to get data from an another system .The aim of the SoC is to process an array of 4096 samples received from the external world.For the data interfacing, we are using GPIO…

    • Answered
    • over 3 years ago
    • Processors
    • Cortex-M / M-Profile forum
  • Is it possible to interface a high frequency sensor-signal output from an analog ASIC chip (e.g. several Kilohertz) using Cortex-M?

    Alexis Ogborn
    Alexis Ogborn

    This question was raised in the ‘Want to maximise your product design? See how a custom ASIC can help?' webinar, view all the questions in the round-up blog post.

    • Answered
    • over 3 years ago
    • DesignStart
    • DesignStart forum
  • CM3 DesignStart Build warning messages with Quartus Prime 17.0.2

    TES
    TES

    Hi,

    I am using Quartus Prime Lite 17.0.2 for building Cortex-M3 DesignStart RTL.

    I can successfully build the RTL, but I got some critical warnings as follows. Can I ignore these warnings? Is there any effects on the design by these warnings?

    Critical…

    • Answered
    • over 2 years ago
    • DesignStart
    • DesignStart forum
  • Test Errors with DesignEval Kit (arm_cortex_m3_designstart_eval_rtl)

    DarshanSatya
    DarshanSatya

    I am currently in Evaluation phase of ARM Design Kits.

    I am using the exact steps present in arm_cortex_m3_designstart_eval_rtl_and_fpga_quick_start_guide_100895_0000_00_en.pdf

    to compile the RTL and run the tests.

    But, unfortunately after compiling the…

    • Answered
    • over 2 years ago
    • DesignStart
    • DesignStart forum
  • BME280 on DesignStart Eval via SPI Shield0

    ag4inst4ll0dds
    ag4inst4ll0dds

    Hello,

    I'm trying to connect the DesignStart Eval System to the BME280 Environmental Sensor via SPI. I used the SPI Shield0 Pins (EXP[11 to 14]) to set the connection and activated alternate functions in uVision for these pins. But how can I set up the…

    • Answered
    • over 2 years ago
    • DesignStart
    • DesignStart forum
  • Interfacing FRDM-K64F with Camera module

    Shwetakr
    Shwetakr

    Hi Team,

    How can we interface FRDM-K64F kit with camera module?

    Thanks & Regards,

    Shweta

    • over 1 year ago
    • Processors
    • Cortex-M / M-Profile forum
  • New AMBA Specification Extends Security to Embedded Design: AMBA 5 AHB5

    Eoin McCann
    Eoin McCann

    The amount of data we generate is growing exponentially. Gartner has predicted that in 2015 the global mobile data traffic will be a total of 52 billion terabytes, an increase of 59 percent on 2014. It’s a staggering number that is driven not just by…

    • over 4 years ago
    • Processors
    • Processors blog