Hi, I'm trying to implement the generic USB mouse functionality on NXP LPC1756. Basing on Keil LED HID example, I modified the USB descriptor as following:
/* HID Report Descriptor */ const uint8_t HID_ReportDescriptor[] = { HID_UsagePage(0x01), HID_Usage(0x02), HID_Collection(HID_Application), HID_Usage(0x01), HID_Collection(HID_Physical), HID_UsagePage(HID_USAGE_PAGE_BUTTON), HID_UsageMin(1), HID_UsageMax(3), HID_LogicalMin(0), HID_LogicalMax(1), HID_ReportCount(3), HID_ReportSize(1), HID_Input(HID_Data | HID_Variable | HID_Absolute), HID_ReportCount(1), HID_ReportSize(5), HID_Input(HID_Constant), HID_UsagePage(HID_USAGE_PAGE_GENERIC), HID_Usage(HID_USAGE_GENERIC_X), HID_Usage(HID_USAGE_GENERIC_Y), //HID_Usage(HID_USAGE_GENERIC_WHEEL), HID_LogicalMin(-127), HID_LogicalMax(127), HID_ReportSize(8), HID_ReportCount(2), HID_Input(HID_Data | HID_Variable | HID_Relative), HID_EndCollection, HID_EndCollection }; const uint16_t HID_ReportDescSize = sizeof(HID_ReportDescriptor); /* USB Standard Device Descriptor */ const uint8_t USB_DeviceDescriptor[] = { USB_DEVICE_DESC_SIZE, /* bLength */ USB_DEVICE_DESCRIPTOR_TYPE, /* bDescriptorType */ WBVAL(0x0200), /* 2.00 */ /* bcdUSB */ 0x00, /* bDeviceClass */ 0x00, /* bDeviceSubClass */ 0x00, /* bDeviceProtocol */ USB_MAX_PACKET0, /* bMaxPacketSize0 */ WBVAL(0xc251), /* idVendor */ WBVAL(0x0116), /* idProduct */ WBVAL(0x0100), /* 1.00 */ /* bcdDevice */ 0x04, /* iManufacturer */ 0x20, /* iProduct */ 0x42, /* iSerialNumber */ 0x01 /* bNumConfigurations */ }; /* USB Configuration Descriptor */ /* All Descriptors (Configuration, Interface, Endpoint, Class, Vendor */ const uint8_t USB_ConfigDescriptor[] = { /* Configuration 1 */ USB_CONFIGUARTION_DESC_SIZE, /* bDescriptorType */ USB_CONFIGURATION_DESCRIPTOR_TYPE, /* bDescriptorType */ WBVAL( /* wTotalLength */ USB_CONFIGUARTION_DESC_SIZE + USB_INTERFACE_DESC_SIZE + HID_DESC_SIZE + USB_ENDPOINT_DESC_SIZE ), 0x01, /* bNumInterfaces */ 0x01, /* bConfigurationValue */ 0x00, /* iConfiguration */ USB_CONFIG_BUS_POWERED /*|*/ /* bmAttributes */ USB_CONFIG_POWER_MA(100), /* bMaxPower */ /* Interface 0, Alternate Setting 0, HID Class */ USB_INTERFACE_DESC_SIZE, /* bLength */ USB_INTERFACE_DESCRIPTOR_TYPE, /* bDescriptorType */ 0x00, /* bInterfaceNumber */ 0x00, /* bAlternateSetting */ 0x01, /* bNumEndpoints */ USB_DEVICE_CLASS_HUMAN_INTERFACE, /* bInterfaceClass */ HID_SUBCLASS_BOOT, /* bInterfaceSubClass */ HID_PROTOCOL_MOUSE, /* bInterfaceProtocol */ 0x00, /* iInterface */ /* HID Class Descriptor */ HID_DESC_SIZE, /* bLength */ HID_HID_DESCRIPTOR_TYPE, /* bDescriptorType */ WBVAL(0x0101), /* 1.01 */ /* bcdHID */ 0x00, /* bCountryCode */ 0x01, /* bNumDescriptors */ HID_REPORT_DESCRIPTOR_TYPE, /* bDescriptorType */ WBVAL(HID_REPORT_DESC_SIZE), /* wDescriptorLength */ /* Endpoint, HID Interrupt In */ USB_ENDPOINT_DESC_SIZE, /* bLength */ USB_ENDPOINT_DESCRIPTOR_TYPE, /* bDescriptorType */ USB_ENDPOINT_IN(1), /* bEndpointAddress */ USB_ENDPOINT_TYPE_INTERRUPT, /* bmAttributes */ WBVAL(8), /* wMaxPacketSize */ 0x0A, /* 10ms */ /* bInterval */ /* Terminator */ 0 /* bLength */ };
Now, when connected to the PC, the Keil MCB1700 board appears as HID-Compliant mouse in Device Manager under Win7, so, I imagine, the descriptor is correct. On USBlyzer the device goes through the GET_DESCRIPTOR and SELECT_CONFIGURATION phases, putting a breakpoint in USB_Configure_Event() function confirms that. Unfortunately nothing happens after, the firmware is supposed to refresh IN report data when GetInReport() function is called at USB Endpoint 1 event. The problem is that this event never happens. In fact, it looks like the host never generates the interrupt condition. I'm missing something but I don't see where exactly to dig. Thanks to all for any eventual advise.
Dimitri
View all questions in Keil forum